2) cast-boronizing layer
铸渗硼层
3) cast-boronization process
铸渗硼工艺
1.
A boronized layer with relatively high hardness and wear－ resistance was formed on the casting surface by using cast－ boronization process.
利用铸渗硼工艺在铸件的表面形成一层硬度较高耐磨性较好的硼化物层，通过对铸渗硼层的显微组织进行分析，发现在铸渗硼剂中加入铜粉可使硼化物层致密，并使铸渗硼层内缩孔、气孔等缺陷较少。
4) boriding
渗硼
1.
Based on these problems, this article provides a new solution of applying the boriding——heat treatment of compound technology of austempering, it makes the face of the mold have the characteristics of high rigidity, strong wear proof and good tenacity, thus makes the li.
针对以上问题,本文采用了渗硼-等温淬火复合强化热处理工艺,使冷镦凹模具有了表面高硬度、高耐磨性与基体具有高强度、高韧性的完美结合,故可使模具使用寿命比常规热处理工艺提高20倍以上。
2.
To improve the anti-corrosion property of low carbon steel in zinc melt,the iron boride is synthesized on the surface of the low carbon steel with solid boriding processing.
为提高低碳钢的抗锌蚀能力,采用固态渗硼工艺在低碳钢的表面形成了致密的铁硼化合物保护层。
3.
Based on a comparative study on the structure and property of powder borided aluminium alloy die casting molds with and without a paint before boriding, a conclusion can be drawn from the experimental results.
在对涂剂粉末渗硼和不涂剂粉末渗硼处理后其组织和性能对比的研究基础上 ,对铝合金压铸模具进行涂剂粉末渗硼 ,试验结果表明 ,涂剂粉末渗硼新工艺是铝合金压铸模具一种实用的强化方法 ,使用寿命提高一倍以
5) boronizing
渗硼
1.
Effect of Boronizing on the Wear Resistance of Gray Cast Iron;
渗硼对灰铸铁耐磨性的影响
2.
Application of boronizing Cr12 steel in drawing die;
Cr12钢渗硼拉深凹模的应用
3.
Effect of rare earth on microstructure and properties of boronizing layer;
稀土对Cr12MoV钢渗硼层组织和性能的影响
6) boron-doping
渗硼
1.
Research on improving the antioxidative ability of porous carbon by solid boron-doping;
固体渗硼提高多孔炭抗氧化性能的研究
2.
It is shown that boron-doping improves the tensile modulus and strength of the fibers.
采用扫描隧道显微镜观察了渗硼处理对碳纤维表面微观形态结构的影响,同时还采用X-ray衍射技术分析了渗硼处理对纤维结构参数的影响。
补充资料：渗硼
分子式：
CAS号：
性质：渗镀品种之一，欲渗入的元素为硼。渗硼方法有固体粉末渗硼、气体渗硼、电解盐浴和盐浴的液体渗硼。渗硼层有优异的耐磨性、较好的耐蚀性和抗高温氧化性。例如钻井设备的泥浆泵零件，冲压、拉丝等模具经渗硼后可提高使用寿命。
CAS号：
性质：渗镀品种之一，欲渗入的元素为硼。渗硼方法有固体粉末渗硼、气体渗硼、电解盐浴和盐浴的液体渗硼。渗硼层有优异的耐磨性、较好的耐蚀性和抗高温氧化性。例如钻井设备的泥浆泵零件，冲压、拉丝等模具经渗硼后可提高使用寿命。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条