1) LiF insulating buffer layer
LiF绝缘缓冲层
2) insulated buffer plate
绝缘缓冲垫板
3) insulation coating
绝缘涂层
1.
Preparation of Al_2O_3/SiO_2 multiphase insulation coating on electric-heating porous SiC ceramics;
电致发热SiC多孔陶瓷Al_2O_3/SiO_2复相绝缘涂层制备
2.
Through test for performance of insulation coating,it is shown that solong as the Al(H_2PO_4)_3/SiO_2 ratio and specific gravity of the solution were controlledproperly,the excellent insulation coating can be obtained.
通过对绝缘涂层的性能试验，研究了绝缘涂层溶液的比重及Ａｌ（Ｈ＿２ＰＯ＿４）＿３与ＳｉＯ＿２比值对绝缘涂层性能的影响，并由此得出只要适当控制Ａｌ（Ｈ＿２ＰＯ＿４）＿３与ＳｉＯ＿２的比值和溶液的比重，便可获性能优良的绝缘涂层。
4) insulator
[英]['ɪnsə,leɪtə, 'ɪnsjə-] [美]['ɪnsə,letɚ, 'ɪnsjə-]
绝缘层
1.
Study on the red thin film electroluminescent devices with ceramic thick film as insulator layer;
以陶瓷厚膜为绝缘层的橙色电致发光器件的研究
2.
Magnetization property and magneto-impedance of dc Joule annealed CuBe/insulator/NiCoP composite wire;
电流退火CuBe/绝缘层/NiCoP复合结构丝的磁化特性和巨磁阻抗效应
3.
Studies on TFEL Device Using Ceramic Thick Film as Insulator Layer;
以陶瓷厚膜为绝缘层的电致发光器件的研究
5) Insulating Coating
绝缘涂层
1.
An Analysis on Mechanism of Insulating Coating's Stripping of Non-oriented Silicon Steel;
无取向硅钢绝缘涂层剥离机理的分析
2.
Amorphous ribbons were dipped into a solution to form insulating coating.
本文采用浸涂后烘干的方法在非晶合金带材的表面形成绝缘涂层,研究了涂层前后非晶合金带材的表面形貌、结构和非晶合金铁芯的磁性能。
6) insulator layer
绝缘层
1.
In the goal to improve this ratio, two insulator layers have been used between the different layers followed by an annealing process at 250℃.
在两磁性层之间加入了绝缘层SiO2,在250℃退火温度下最大阻抗效应为62%。
2.
The ZnO films deposited on insulator layer were characterized by X-ray diffractometry and atomic force microscopy.
用X射线衍射仪、原子力显微镜对生长在绝缘层上的ZnO薄膜进行了表征。
3.
It is reported in this paper that red ZnS∶Sm, Cl thin film electroluminescent devices using ceramic thick film as insulator layer (CTFEL) have been manufactured firstly.
这类显示器的创新表现在采用丝网印刷的几十个微米量级的高介电常数的陶瓷厚膜来替代无机薄膜电致发光器件中的薄膜绝缘层。
补充资料：缓冲层
分子式：
CAS号：
性质：斜交轮胎胎面与胎体之间的胶布层或胶层。其主要作用是缓和外来冲击，防止外层胶的龟裂直接抵达胎体帘布层，并承受轮胎在行驶时或突然停止时，由于惯性作用而产生的剪切应力。为此，它应具有较好的导热性、耐老化性、多次变形下的耐疲劳性和低生热性及耐热性等。所用的帘线强度必须高于胎体帘线。
CAS号：
性质：斜交轮胎胎面与胎体之间的胶布层或胶层。其主要作用是缓和外来冲击，防止外层胶的龟裂直接抵达胎体帘布层，并承受轮胎在行驶时或突然停止时，由于惯性作用而产生的剪切应力。为此，它应具有较好的导热性、耐老化性、多次变形下的耐疲劳性和低生热性及耐热性等。所用的帘线强度必须高于胎体帘线。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条