1) fiber number
纤维数量
1.
The average transverse area, total fiber number and fiber diameter of posterior lateral line nerve were examined quantitatively by morphologic analysis sys.
运用形态分析系统软件对后侧线神经的横截面积、纤维数量和纤维直径进行了定量的统计分析。
2) represent parameter of steel-fiber content
钢纤维含量特征参数
3) fiber content
纤维掺量
1.
The variation between fiber content and compressive strength,splitting strength were analyzed.
为了研究纤维掺量对沥青混凝土强度的影响,选用5种纤维掺量沥青混凝土的马歇尔试件和圆柱体试件,在MTS810材料试验机上进行劈裂试验和单轴压缩试验,分析了劈裂试验结果和抗压强度随纤维掺量变化的规律。
2.
When the base strength grade is in the range of C30~C50,and thread steel fiber content is 0~1.
5%掺量范围内,对抗压强度的增强作用明显;当基体强度等级达到C60,纤维掺量在0。
3.
The viscoelastic performance was simulated by using four-unit five-parameter model,its parameters were obtained from the data of the test,and a four-unit five-parameter viscoelastic constitutive model with fiber content was set up.
根据粘弹性力学理论,采用"四单元五参数"模型(修正的Bugers模型)模拟纤维沥青混凝土的粘弹性能,其参数值由试验数据的数值拟合获得,提出了计入纤维掺量的"四单元五参数"粘弹性本构模型。
4) Fiber content
纤维含量
1.
The influence of the short fiber content,fiber length and hybrid effect on the tensile,flexual and impact properties are mainly discussed.
本文讨论了模压成型制成的短纤维增强PVC的制备方法和力学性能,主要探讨了纤维含量、纤维长度、混杂纤维效应等对复合材料拉伸、弯曲和冲击性能的影响。
2.
The tensile strength, flexural and impact strength of samples with different fiber contents are investigated by comparing three kinds of composites with fiber contents of 10,20 and 30wt%.
将纤维重量含量分别为 10 %、2 0 %和 30 %的复合材料进行比较 ,分析纤维含量对复合材料拉伸、弯曲和冲击性能的影响 ;将纤维分别切成约 3mm、5mm和 10mm长制成复合材料进行比较 ,分析纤维长度对复合材料拉伸、弯曲和冲击性能的影响。
3.
Wearability of composites with different fiber orientation and different fiber content has been analyzed.
着重研究了纤维取向、纤维含量、外加载荷的变化对复合材料磨损性能的影响、通过对磨痕扫描电镜的观察，探讨了复合材料的磨损机理。
5) Fiber quality
纤维质量
1.
A study on the wood properties,fiber quality and pulping performance of bamboo-willow
竹柳材性、纤维质量及制浆性能的研究
2.
Study on the fiber quality parameter by FQA in different recycling time(0s、5s、10s、15s、20s), combining Zeta potential,surface tension and so on, appraise secondary fiber deinking efficiency by the pulp brightness.
在脱墨浆适宜的工艺条件下,使用纤维质量分析仪FQA测量了不同碎解时间(0s、5s、10s、15s、20s)下的纤维形态参数,并结合电导率、Zeta电位、表面张力、浊度等参数,通过白度评价了二次纤维脱墨的效果,结果表明进口旧新闻纸的最佳碎解时间为15s。
3.
Measures for determining the fiber quality, effects of fiber on MDF quality, and measures for improving the fiber quality were described.
介绍如何判定纤维质量、纤维质量对中纤板质量的影响和改善纤维质量的措施。
6) fibre Content
纤维含量
1.
The methods of determining the resin and fibre contents in the composite are also introduced.
同时介绍了复合材料中树脂和纤维含量的确定方法。
补充资料：碳(石墨)纤维增强体(见碳纤维、石墨纤维)
碳(石墨)纤维增强体(见碳纤维、石墨纤维)
earbon(graPhite)fibrereinforeements
，、、里z耽维增强体earbon(graphi现inforcements用于复合材料中承受负荷，田的磷纤始知五史纤俯亡e)fibre起增强作
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条