1)  gray cast iron
灰铸铁材料
1.
The technology of Ni-P alloy electro-brush plating for repairing the cycloid pump body which was manufactured with gray cast iron and worn was studied.
研究了摆线泵泵体(灰铸铁材料制造)磨损后,刷镀Ni-P合金修复工艺。
2)  gray iron
灰铸铁
1.
Micro-plasma arc surface treatment of gray iron;
灰铸铁微束等离子弧表面处理的研究
2.
The melt treating techniques used for the production of low alloyed hi-strength gray iron and vermicular iron cylinder blocks and heads were summarized.
综述了用作发动机缸体缸盖的低合金高强度灰铸铁和蠕墨铸铁的铁液处理技术。
3.
The factors influencing the cutting machinability of gray iron cylinder blocks were summarized including chemical composition, melting and inoculating processes, graphite and hard particles in the matrix.
综述了影响灰铸铁缸体切削加工性的因素,包括化学成分、熔炼及孕育处理方法、石墨和基体组织中的硬质点。
3)  gray cast iron
灰铸铁
1.
Effect of tin on the microstructure, properties and corrosion resistance of gray cast iron;
锡对灰铸铁组织性能及耐蚀性的影响
2.
Friction and wear of ceramics against gray cast iron in distilled water;
水润滑下陶瓷与灰铸铁副的滑动磨损特性
3.
The gray cast iron samples reinforced by surface modified SiC nano-powders were prepared under industrial conditions by foundry method.
在生产条件下采用冲入铸造法制备了改性纳米SiC粉体强化灰铸铁材料。
4)  Grey iron
灰铸铁
1.
Effects of parameters of laser microprecision treatment on antiwear behavior of grey iron;
激光微精处理参数对于灰铸铁耐磨性能的影响
2.
Grey iron with high strength above HT250 can be achieved by adjusting Si/C ratio even if without applying traditional inocul.
8%时 ,Si/C对灰铸铁金相组织与机械性能的影响 ,结果表明 :当Si/C从 0 。
3.
This paper studies the technique of laser surface treatment of grey iron.
2kW CO_2激光加工机重熔普通灰铸铁表面并进行合金化处理。
5)  Gray iron casting
灰铸铁件
1.
This paper introduces the special properties of repair welding small defects for gray iron castings.
介绍了灰铸铁件小缺陷的特殊性 ,从焊补工艺上和材料的选用两方面考虑 ,有效地降低了焊接裂纹的产生 ,使母材与焊补金属熔合良好。
6)  Gray Cast HT200
灰铸铁HT200
参考词条
补充资料：灰铸铁
分子式：
分子量：
CAS号：

性质：含有片状石墨的铸铁。断口呈深灰色。具有优良的铸造、切削加工、抗磨、滑润、消振等性能，但强度较差，不能锻轧。常用在化工机械制造中。代号HT（huitie的缩写），加以最低抗拉强度σb及抗弯强度σw的数值。例如HT18－36，即表示σb≥176.4兆帕（18公斤力／毫米2），σw≥356.8I兆帕（36公斤力／毫米2）的铸铁。

说明：补充资料仅用于学习参考，请勿用于其它任何用途。