1) dephosphorization of stainless steel
不锈钢脱磷
2) Oxidizing Dephosphorization of Stainless Steel Liquid
不锈钢母液-氧化脱磷
4) stainless steel
不锈钢
1.
Vacuum hot roll bonding of TC4 titanium alloy and 0Cr18Ni10Ti stainless steel;
TC4钛合金与0Cr18Ni10Ti不锈钢真空热轧连接
2.
Research on cyclic ion nitriding technology catalyzed by rare earth for 2Cr13 stainless steel;
2Cr13不锈钢的稀土催渗循环离子渗氮工艺研究
3.
Analysis of the components of acid chemical coloring solutions for stainless steel;
不锈钢酸性化学着色液成分的分析方法
5) 2Cr13 stainless steel
2Cr13不锈钢
1.
Influence of the TiN film layer on the anti-erosion performance of the 2Cr13 stainless steel blade
TiN膜层提高2Cr13不锈钢叶片的抗冲刷腐蚀性能
2.
Study of hot deformation microstructure and properties for 2Cr13 stainless steel containing rare earth Y
含稀土元素Y的2Cr13不锈钢热变形组织与性能研究
3.
Effect of tempering temperature on stress-corrosion cracking and mechanical hysteresis of 2Cr13 stainless steel
回火温度对2Cr13不锈钢应力腐蚀开裂和力学滞后的影响
6) 1Cr13 stainless steel
1Cr13不锈钢
1.
Vacuum brazing between TiC/NiCr cermets and 1Cr13 stainless steel;
TiC/NiCr金属陶瓷与1Cr13不锈钢的真空钎焊
2.
Titanium coating had been deposited on 1Cr13 stainless steel substrate using cold spray technique.
0MPa,载气温度为500℃的状态下,用冷喷涂的方法在1Cr13不锈钢基体上制备了钛金属涂层。
3.
TiC/Ti(C, N)/TiN multi-layer coatings are prepared on the 1Cr13 stainless steel substrate by the technique of Chemical Vapour Deposition, and the fretting wear behaviour of 1Cr13 stainless steel and TiC/Ti(C, N)/TiN coatings are investigated and studied contrastively from 25℃ to 400℃ in the gross slip regime.
采用化学气相沉积(CVD)技术,在1Cr13不锈钢基体上制备TiC/Ti(C,N)/TiN复合涂层。
补充资料：A2/O生物除磷脱氮法
分子式：
CAS号：
性质：(厌氧、缺氧/好氧)法是在A2/O（厌氧/好氧）法基础上增加一个缺氧段（A），在缺氧过程中，微生物大量吸附厌氧过程释放的磷和原废水中的磷，在细菌细胞体内合成聚磷酸盐而贮存起来，最后通过沉淀池的剩余污泥排放而达到除磷的目的。A2/O系统的特点是污泥龄长，剩余污泥量少，运行稳定，而冲击负荷。
CAS号：
性质：(厌氧、缺氧/好氧)法是在A2/O（厌氧/好氧）法基础上增加一个缺氧段（A），在缺氧过程中，微生物大量吸附厌氧过程释放的磷和原废水中的磷，在细菌细胞体内合成聚磷酸盐而贮存起来，最后通过沉淀池的剩余污泥排放而达到除磷的目的。A2/O系统的特点是污泥龄长，剩余污泥量少，运行稳定，而冲击负荷。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条