2) lineation method
划线方法
1.
Passing throrgh analysing of the original lineation method,finding out that it is unsuited to the reasonableness.
通过对原划线方法的认真分析,找到其不合理性。
3) F line-method
F划线法
4) linear programming method
线性规划法
1.
By taking the minimum cost as optimization aim,the synthetic factor method,minimum cost method,and linear programming method of solving assembled dimensional chains are introduced.
以最低制造成本为优化目标，介绍了求解装配尺寸链的综合因子法、最低成本法和线性规划法，为合理分配装配尺寸链中各环公差提供参考。
2.
Basing on the monochromatic radiative intensity,the inverse problem of radiative transfer equation was solved by least squares method,regularization method and linear programming method.
针对轴对称光学薄火焰,用图像探测器和滤色片获得火焰的单色辐射图像,根据火焰的单色辐射强度,分别采用最小二乘法、正则化方法和线性规划法对辐射传递逆问题进行了求解。
5) linear programming
线性规划法
1.
In order to optimize the sinter mix proportioning, three different kinds of optimizing methods, Linear Programming, Monte Carlo Algorithm and Genetic Algorithm, were used to calculate proportioning scheme ,under the identical conditions, and optimum solutions were analyzed from the final solution, efficiency, convenience and other aspects.
本文通过运用线性规划法、蒙特卡洛法和遗传算法对相同的烧结配料问题进行优化,并对得到的结果进行了分析,从最终结果、求解效率、易用性等方面比较了3种方法的优劣,最后得出结论:遗传算法更适应今后烧结配料优化的计算要求。
2.
The physical meaning of reflection coefficients has been discussed,and the underdetermined system of equations which contain reflection coefficients has been reached in the time-domain , the method of Linear Programming for solving the underdetermined system of equations has been put forward, and the train of thought and programming frame has been given.
讨论了在水平层状介质中的反射系数的物理意义 ,推出时间域含有以反射系数序列为未知项的欠定方程组 ,提出用线性规划法求解瞬变电磁场反射系数序列 ,并给出求解思路和程序框图。
3.
Using linear programming method into a small valley land planning in Danjiangkou Reservoir zones,the rational allocation of resources is achieved for maximum effectiveness.
把线性规划法运用于丹江口库区小流域土地规划,以便实现资源的合理配置,发挥最大效益。
6) streaking inoculation
分区划线法
1.
Results Perform streaking inoculation,multipoint inoculation and microculture in one Sabourand s agar.
方法在同一个平板内用分区划线法、多点接种法及小培养对标本进行培养,分离假丝酵母菌。
补充资料：划线
按图纸要求在工件上划出加工界线、中心线和其他标志线的钳工作业。单件和中、小批量生产中的铸锻件毛坯和形状比较复杂的零件，在切削加工前通常需要划线。划线的作用是：①确定毛坯上各孔、槽、凸缘、表面等加工部位的相对坐标位置和加工面的界线，作为在加工设备上安装调整和切削加工的依据；②对毛坯的加工余量进行检查和分配，及时发现和处理不合格的毛坯。划线一般在平台上进行（图1）, 常用的划线工具有划针、划针盘、划规、直角尺、游标高度尺、钢板尺、方箱、 V形铁、千斤顶、楔铁和中心冲等（图2）。为了能划出清晰的线条，一般在毛坯表面上先涂一层白色石灰水，对已经加工过的表面则涂普鲁士蓝加漆片和酒精的混合液。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条