1) minimum throat radius
最小孔喉半径
1.
The lower limit of porosity of the gas and oil reservoirs in the eastern sag of Liaohe Oilfield was calculated by using the method of minimum throat radius and in combination with the capillary pressure curve.
运用最小孔喉半径法,结合毛管压力曲线,对辽河油田东部凹陷气藏和油藏的储层孔隙度下限值分别进行了计算。
2) pore throat radius
孔喉半径
1.
Study of variation rule in pore throat radius of reservoir in later development stage and harness countermeasures.;
开发后期储层孔喉半径变化规律研究及治理对策
3) minimum flowing pore throat diameter
可流动最小孔喉直径
4) minimum radius
最小半径
1.
Research on Method to Confirm Minimum Radius of Circular Curve of Mountain Expressway;
山区高速公路圆曲线最小半径确定方法的研究
2.
According to the speed and overload during vertical maneuver,the minimum radius, its speed as well as rapid rotating speed are calculated and analyzed for upward level flight, downward inverted flight and vertical ma-neuver.
根据某新机飞行人员的要求,对其正飞向上,倒飞向下和垂直位置进行机动的最小半径及其速度、快转速度进行了一系列的计算与分析,从中得出飞机中低空(1000～5000米)进行垂直机动的最佳速度和过载,为某新机垂直机动训练中,提高质量,保证安全提供了可行的理论依据,并在飞行训练中得到了验证。
3.
This paper considers the minimum radius problem of ball-coverings with the cardinality m(≥n+1) in n by the neural network method.
本文采用神经网络方法研究n中球覆盖最小半径的计算问题,重新给出计算基数为m(≥n+1)的球覆盖最小半径的公式(对于m=2n(对称)和m=n+1给出了解析表达式),然后基于罚函数法建立神经网络模型,该模型的平衡点集具有大范围吸引性且(渐近)稳定平衡点等价于(严格)极大值点。
5) apex versus pore aperture
峰点孔喉半径
1.
Pittman in reprocessing the mercury injection curves obtained from reservoirs in the third member of Shahejie Formation in Huimin sag,the apex versus pore apertures are determined and their relationship with porosities and permeabilities is established.
Pittman的方法对惠民凹陷沙河街组三段储层的压汞曲线重新处理,确定了峰点孔喉半径,建立了峰点孔喉半径与孔隙度、渗透率之间的关系,分析其峰点孔喉半径与含油性间的关系,表明惠民凹陷沙河街组三段为常压背景下的岩性圈闭或构造-岩性圈闭,若具备油源供给,圈闭中含油砂层的最小峰点孔喉半径取决于油柱高度。
6) pore throat mean radius
孔喉均值半径
补充资料：最小弯曲半径
最小弯曲半径
minimum bending radius
zu一x一00 wanqu banjing最小弯曲半径(minimum bending radius) 板带材围绕在圆杆上进行弯曲而不产生表面裂纹时的最小圆杆半径。它表征了材料的最基本的弯曲性能。通常用板带厚度的倍数来表示。冷弯型材成形时的最小弯曲半径还要考虑弯曲角、弯曲长度、材料性能、垂直于弯曲线的切边状况以及与板带轧制方向有关的弯曲取向等的影响。一般，低碳钢、低合金高强度钢板带的最小弯曲半径为其厚度的l~4倍。 (妇七健)
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条