1) vice thrust bearing
副推力瓦
1.
The main oil pumps are the key equipment of lubrication system for the steam turbine group and wear of their vice thrust bearings usually occur in the process of operating.
主油泵是汽轮机组润滑系统的关键设备,在运行过程中经常出现副推力瓦磨损的现象。
2) thrust pad
推力瓦
1.
The analysis and handling of turbine A2 with higher differential expansion in HP cylinder and higher temperature in thrust pad of Shajiao Power Plant A of Guangdong;
广东沙角A厂2#汽轮机高压缸胀差过大和推力瓦温度过高的分析和处理
2.
The couple of force created by rotor pole center suspending difference may not increase the pressure on the thrust pad.
转子磁场中心安装偏差所产生的轴向磁拉力很小,转子磁极中心挂装高程差所产生的不平衡力偶不致增大推力瓦受力。
3.
Numerical analysis method was used to study the lubricating properties of three-dimensional sector-shaped slope thrust pad.
为研究三维扇形斜面平台推力瓦的润滑性能,采用数值分析方法,通过Matlab软件计算水膜厚度、压力分布,使用有限元ANSYS软件获得推力瓦位移场和温度场的分布规律。
3) thrust bearing
推力瓦
1.
An analysis is presented,of what caused the temperature,of the front thrust bearing pads,of a 135 MW set,to rise excessively during power escalation.
对某135 MW机组升负荷过程中出现的汽轮机正向推力瓦温度升高的故障进行分析,找到导致瓦块温度偏高的原因是A4腔漏汽至三抽的排汽不畅,并提出了改进措施。
2.
The paper analyzes, in detail, what caused the thrust bearing pads of the steam turbinegenerator to wear off and reports on the corresponding improving measures taken, which paved to be remarkably effective.
该文详细分析了造成汽轮发电机组主油泵推力瓦磨损的原因,介绍了所采取的相应改进措施,以及取得的显著成效。
3.
Through analyzing the cause of burnout of the thrust bearing of motorized feed water pump for unit 3 in Zhangjiakou Power Plant, the reason of over-temperature of non-working surface of the thrust bearing is found out, thus provides a correct way to analyze and solve the failure of thrust bearing caused by over temperature.
通过对张家口发电厂#3机组电动给水泵烧瓦的分析 ,找出了非工作面推力瓦温度过高的原因 ,为正确分析及解决温度升高导致的推力瓦设备损坏提供了思路。
4) thrust bearing pad
推力瓦
1.
The temperature of thrust bearing pad exceeds the designed alarm temperature and continues the rising of No.
冶勒水电站1号机组在试运行过程中推力轴承温度超过设计的报警温度,且一直上升无法继续运行,通过在瓦盖上增加通油孔,加大油通路;取消冷却器套管;增加6个冷却器及1套冷却供、排水管路等;使推力瓦温度降至64。
2.
That the temperature of thrust bearing pad exceeds the alarm temperature designed for unit No.
停机分析后认为,可能是推力瓦受力不均、热交换量不够、冷却系统本体存在缺陷等所致。
3.
Burning accident can be resulted from non uniform pressure on the thrust bearing pad due to under performance of installation and equipment.
如果安装质量和设备缺陷引起推力瓦在运行中受力不均 ,会导致推力瓦烧损。
5) thrust tile
推力瓦
1.
Domestic main oil pump thrust tile of 300MW steam turbine wears and tears the trouble,happen timely in recent years.
国产300MW汽轮机主油泵推力瓦磨损故障近年来时有发生。
2.
Aiming at the thrust tile abrasion of a 300MW unit,the reasons are analyzed,the diagnosis and treatment is get out,which have achieved the anticipatory effects.
对某电厂300MW机组推力瓦磨损原因进行了计算分析,对推力瓦磨损作出了正确的故障诊断,提出了具体的防范措施,达到了预期效果。
3.
From the operation survey to synchronic motor thrust tile,this paper analyzes the causation of wearing producing and poses the treating measure.
通过对同步电机推力瓦的运行检测 ,分析同步电机推力瓦产生磨损的原因并提出处理措施。
6) thrust pad
推力瓦块
1.
Aimed at some problems of YT62 hydraulic coupling occurred frequently in actual operation,such as too high temperature of of side thrust bearings,burnout of thrust pads,and rupture of impeller blades,the paper analyzes and discusses causes of these faults,and puts forward some effective treatments schemes and improvement methods.
本文针对YT62型液力偶合器在实际运行过程中经常出现的泵轮侧推力轴承温度偏高、泵轮和涡轮侧推力瓦块烧毁以及泵轮叶片断裂等故障进行了原因分析及探讨,并提出了有效的处理方案和改进措施。
补充资料：瓦利副奇号航空母舰
名称：瓦利副奇号航空母舰
所属国家：美国
武器分类：航空母舰
军种分类：海军
相关资料：
瓦利副奇号航空母舰(valley forge)由费城海军船厂建造，1945年9月7日开工，1945年11月18日下水，1946年11月3日服役。1953年11月12日设计改装为反潜航母（cvs 45）1961年3月到1961年7月改装为两栖攻击舰(lph 8)。后进行了fram ii延寿改装。1970年1月15日退役。1971年10月29日被卖出拆毁。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条