1)  irregular shape
非规则任意形状
2)  non-sanitary
非规范
1.
Horizontal migration rule and control measures of landfill gas arising from non-sanitary municipal solid waste landfill;
非规范生活垃圾填埋场填埋气横向迁移规律及控制
3)  Irregular grid
非规则网
4)  abnormal beam
非规则梁
1.
Based on the bifurcation buckling of abnormal beamcolumn steel frame,it was found that the way to ascertain column s effective length of normal steel frame can also be used in abnormal beam-column steel frame;the principle of virtual work was used to deduce the flexural stiffness of two kinds of Abnormal beams,and its effect on the effective length of rigid steel frame column was analyzed.
针对钢结构非规则梁柱体系弹性分岔屈曲失稳的特点,认为普通钢框架考虑梁、柱线刚度比值关系确定刚架柱计算长度的方法仍适用于非规则框架中的框架柱。
5)  irregular
非规则
1.
Influence of performance parameters of isolated irregular structures on earthquake responses;
平面非规则隔震结构性能参数对地震反应的影响
2.
Simplified dynamic analysis for irregular tier building with consideration of floor deformation;
非规则多层建筑楼板变形动力性能分析
3.
Calculation analysis of torsion and local deformation of plane irregular house structure arrangement (revision);
平面非规则房屋结构扭转和局部变形的计算
6)  irregular wave
非规则波
1.
Using developed systems for measuring surface wave and hydrodynamic pressure variation, various surface waves(ship wavemaking, regular wave,irregular wave and wave pattern caused by a moving ship in wave) and pressure fluctuations on sea bottom were measured.
依据研制的表面波和水底压力联合测量系统 ,对舰船兴波、规则波、非规则波和舰船在波浪中航行的水面波形以及它们在水底引起的压力脉动进行了测量 ,初步分析了表面波与水底压力脉动之间的关系 。
2.
This paper introduces the testing of simulation performance of the regular wave and irregular wave of the import wave maker after its hardware and software are reformed.
通过改进后的水池造波系统对工程中常用的规则波和二维非规则波浪的模拟试验,研究了该造波系统的最大造波能力、波浪总谐波变形以及对随机波浪谱的模拟精度等波浪模拟性能。
参考词条
补充资料:ANSYS中在任意面施加任意方向任意变化的压力方法
在任意面施加任意方向任意变化的压力
在某些特殊的应用场合,可能需要在结构件的某个面上施加某个坐标方向的随坐标位置变化的压力载荷,当然,这在一定程度上可以通过ANSYS表面效应单元实现。如果利用ANSYS的参数化设计语言,也可以非常完美地实现此功能,下面通过一个小例子描述此方法。
!!!在执行如下加载命令之前,请务必用选择命令asel将需要加载的几何面选择出来
!!!
finish
/prep7
et,500,shell63
press=100e6
amesh,all
esla,s
nsla,s,1
! 如果载荷的反向是一个特殊坐标系的方向,可在此建立局部坐标系,并将
! 所有节点坐标系旋转到局部坐标系下.
*get,enmax,elem,,num,max
dofsel,s,fx,fy,fz
fcum,add !!!将力的施加方式设置为"累加",而不是缺省的"替代"
*do,i,1,enmax
*if,esel,eq,1,then
*get,ae,elem,i,area !此命令用单元真实面积,如用投影面积,请用下几条命令
! *get,ae,elem,i,aproj,x !此命令用单元X投影面积,如用真实面积,请用上一条命令
! *get,ae,elem,i,aproj,y !此命令用单元Y投影面积
! *get,ae,elem,i,aproj,z !此命令用单元Z投影面积
xe=centrx !单元中心X坐标(用于求解压力值)
ye=centry !单元中心Y坐标(用于求解压力值)
ze=centrz !单元中心Z坐标(用于求解压力值)
! 下面输入压力随坐标变化的公式,本例的压力随X和Y坐标线性变化.
p_e=(xe-10)*press+(ye-5)*press
f_tot=p_e*ae
esel,s,elem,,i
nsle,s,corner
*get,nn,node,,count
f_n=f_tot/nn
*do,j,1,nn
f,nelem(i,j),fx,f_n !压力的作用方向为X方向
! f,nelem(i,j),fy,f_n !压力的作用方向为Y方向
! f,nelem(i,j),fz,f_n !压力的作用方向为Z方向
*enddo
*endif
esla,s
*enddo
aclear,all
fcum,repl !!!将力的施加方式还原为缺省的"替代"
dofsel,all
allsel
说明:补充资料仅用于学习参考,请勿用于其它任何用途。