1) micro-power Hall sensor
低功耗霍尔传感器
2) Hall sensor
霍尔传感器
1.
Application of the Hall sensor in the rotating speed of locomotive;
霍尔传感器在机车测速中的应用研究
2.
High accuracy magnetic field measurement methods based on Hall sensor;
基于霍尔传感器的高准确度磁场测量方法
3.
Hall sensor test system based on single chip microcontroller;
基于单片机的霍尔传感器测试系统
3) Hall transducer
霍尔传感器
1.
Improving the precision of Hall transducer;
提高霍尔传感器精确度的研究
2.
The principle of monitoring steel-cord conveyor belt joint breaking by Hall transducer and the mathematics model of measuring the belt joint elongation is discussed.
论述了用霍尔传感器通过测量接头拉伸量来进行钢绳芯输送带接头损伤和断裂状况监测的原理以及用于测量诊断的数学模型，并研制成功包括霍尔传感器与变送器、以及Ｚ－８０上开发的故障诊断软件在内的一套监测系统，该系统可用于皮带损坏、断裂信号的拾取、贮存、处理、诊断和预报等。
3.
A kind of magnetic sensor array based on UGN3503U linear Hall transducer was presented.
叙述了一种基于UGN3503U线性霍尔传感器的磁敏传感器阵列。
4) Hall sensors
霍尔传感器
1.
Rotor position measurement of permantent maglev heart pump by use of Hall sensors;
应用霍尔传感器测量无源磁浮心脏泵转子位置
2.
The system uses single chip micro-controller combining Hall sensors as predictive data acquisition system,which sends acquired data to PC via serial port,and then the PC analyzes,processes,displays and saves these data in LabVIEW environment.
该系统将单片机为核心的小系统,结合霍尔传感器作为前端的数据采集系统,将采集到的数据利用串口传送到PC主系统。
3.
In order to provide the convenience of simulation about integrated Hall sensors, magnetic field model and Hall model are build in Ver- .
可用于设计集成霍尔传感器的整体设计,将磁信号转换为电信号。
5) Hall effect sensor
霍尔传感器
1.
By means of the sensitivity of the Hall effect sensor to geomagnetic field, the in.
在立轴支承的转盘中央安装一个平面反射镜,在转盘的圆周边缘处安装一个霍尔传感器。
2.
Presented the design and architecture implementation of AC servo control system for permanent magnet synchronous motor with sinusoidal flux distribution using linear Hall effect sensors as the motor feedback devices.
由于安装在永磁同步电机定子上的线性霍尔传感器的输出模拟信号与转子气隙磁场强度成比例,与反电动势同相位,通过使用线性霍尔传感器代替光电编码器和开关霍尔传感器,可得到转子的位置和速度信息;在此基础上,给出一种不需要在静止坐标系和旋转坐标系之间相互变换,可以在静止坐标系中直接产生相电流命令的磁场定向控制算法。
6) Hall current sensor
霍尔电流传感器
1.
Application of Hall current sensor in electric welding machine;
霍尔电流传感器在电焊机中的应用
2.
Temperature compensation of Hall current sensor based on two-dimensional regression analysis
基于二维回归分析法的霍尔电流传感器温度补偿
3.
The Hall current sensor is used to collect the real-time machining current,and the process data curves are displayed real-timely and dynamically to show the rapid response of the current break.
在虚拟仪器软件平台上研制了电化学微细加工监控系统,系统采用霍尔电流传感器采集加工电流,并实时准确显示过程数据曲线,根据电流突变快速响应,系统的定位精度和重复定位精度均小于5μm。
补充资料：功耗
功率的损耗。电路中通常指元、器件上耗散的热能。有时也指整机或设备所需的电源功率。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条