1) aluminum cooling board
铝合金冷板
2) aluminum alloy sheet
铝合金板
1.
Parameter prediction of bending of aluminum alloy sheet induced by laser prompt heating;
铝合金板快速加热弯曲的参数预测
2.
Tribotest at drawbead in aluminum alloy sheet warm forming;
铝合金板温成形过程中拉深筋处摩擦的测量
3.
Finite element analysis on mechanical behavior of adhesive joint of steel sheet and aluminum alloy sheet;
钢板与铝合金板胶接接头力学性能的有限元分析
3) aluminum alloy plate
铝合金板
1.
Center-cracked aluminum alloy plates were adhesively one-side bonded with unidirectional carbon/ epoxy composite patches by vacuum-bagging process.
利用袋压工艺、采用单向碳纤维/环氧复合材料补片对含中心裂纹的铝合金板进行了修补,测试了胶接修补前后板的静态力学性能和疲劳性能。
2.
The aluminum alloy plate for adhesive bonding was anodized in the solution of phosphoric acid and its adhesion performance was studied.
采用磷酸电解质对铝合金板进行了阳极化处理并测试了其胶接性能,测试了阳极化过程中铝合金板的基本力学性能,观察了阳极化处理后的铝合金板的表面形貌,分析了阳极化处理后铝合金粘接副的胶接界面、拉伸剪切失效模式。
3.
ANSYS finite element analysis method was adopted to analyze the rigidity of a center holed aluminum alloy plate, and to investigate the influence of hole on rigidity and stress area disturbed.
用ANASY有限元分析软件对复合材料修复铝合金结构的刚度进行数值分析,研究了开孔损伤对铝合金板结构刚度和应力扰动区范围的影响。
4) aluminium alloy sheet
铝合金板
1.
Research and development of friction and lubrication for aluminium alloy sheet forming;
铝合金板成形中摩擦与润滑的研究进展
2.
Formability window of aluminium alloy sheet at variable blank-holder force;
变压边力条件下铝合金板的成形窗口
3.
In order to exactly evaluate drawability of automotive aluminum alloy sheets, the correlation between material properties and formability of automotive aluminium alloy sheets, based on the sample data obtained from uniaxial tension, plane strain tension and cylindrical deep drawing tests, is analyzed by means of regression analysis method.
为了准确地评估汽车用铝合金板的拉深性能,在单向拉伸试验、平面应变拉伸试验和圆筒件拉深试验获得的样本基础上,采用回归分析方法,全面地分析了汽车用铝合金板各种材料性能参数与其拉深性能之间的对应关系。
5) aluminium alloy plate
铝合金厚板
1.
Review about supply and demand of global aluminium alloy plate for aviation;
全球航空级铝合金厚板供需述评
6) aluminum alloy sheet
铝合金薄板
1.
Theoretical inquiry into ductile fracture mechanism and modification of ductile fracture criterion based on aluminum alloy sheet;
韧性断裂机理的理论探讨与基于铝合金薄板韧性断裂准则的修正
2.
2 mm thick 5A06 aluminum alloy sheet with filler wire were investigated based on the existing problems by YAG laser welding of sheet plate,which included narrow scope of welding procedure and strict restriction of the gap tolerance and so on.
2mm厚5A06铝合金薄板YAG激光焊接工艺范围窄和对间隙要求严格等问题,较系统地研究了该铝合金激光填丝焊接工艺。
补充资料：氟碳涂层铝合金装饰板制成的铝合金幕墙建筑物
氟碳涂层铝合金装饰板制成的铝合金幕墙建筑物
J氟碳涂层铝合金装饰板制成的铝合金幕墙建筑物
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条