1) 301 stainless steel
301不锈钢
1.
Compressive properties of AISI 301 stainless steel with gradient structure near surface layer;
具有梯度结构表层301不锈钢的压缩性能
2) stainless steel
不锈钢
1.
Vacuum hot roll bonding of TC4 titanium alloy and 0Cr18Ni10Ti stainless steel;
TC4钛合金与0Cr18Ni10Ti不锈钢真空热轧连接
2.
Research on cyclic ion nitriding technology catalyzed by rare earth for 2Cr13 stainless steel;
2Cr13不锈钢的稀土催渗循环离子渗氮工艺研究
3.
Analysis of the components of acid chemical coloring solutions for stainless steel;
不锈钢酸性化学着色液成分的分析方法
3) 2Cr13 stainless steel
2Cr13不锈钢
1.
Influence of the TiN film layer on the anti-erosion performance of the 2Cr13 stainless steel blade
TiN膜层提高2Cr13不锈钢叶片的抗冲刷腐蚀性能
2.
Study of hot deformation microstructure and properties for 2Cr13 stainless steel containing rare earth Y
含稀土元素Y的2Cr13不锈钢热变形组织与性能研究
3.
Effect of tempering temperature on stress-corrosion cracking and mechanical hysteresis of 2Cr13 stainless steel
回火温度对2Cr13不锈钢应力腐蚀开裂和力学滞后的影响
4) 1Cr13 stainless steel
1Cr13不锈钢
1.
Vacuum brazing between TiC/NiCr cermets and 1Cr13 stainless steel;
TiC/NiCr金属陶瓷与1Cr13不锈钢的真空钎焊
2.
Titanium coating had been deposited on 1Cr13 stainless steel substrate using cold spray technique.
0MPa,载气温度为500℃的状态下,用冷喷涂的方法在1Cr13不锈钢基体上制备了钛金属涂层。
3.
TiC/Ti(C, N)/TiN multi-layer coatings are prepared on the 1Cr13 stainless steel substrate by the technique of Chemical Vapour Deposition, and the fretting wear behaviour of 1Cr13 stainless steel and TiC/Ti(C, N)/TiN coatings are investigated and studied contrastively from 25℃ to 400℃ in the gross slip regime.
采用化学气相沉积(CVD)技术,在1Cr13不锈钢基体上制备TiC/Ti(C,N)/TiN复合涂层。
5) 254SMo stainless steel
254SMo不锈钢
6) 316L stainless steel
316L不锈钢
1.
Warm compaction technics of 316L stainless steel powder;
316L不锈钢粉末的温压工艺研究
2.
Influence of heat-treatment on the microstructure and properties of 316L stainless steel;
热处理对316L不锈钢组织和性能的影响
3.
Effect of surface mechanical attrition treatment on microstructures and mechanical properties of 316L stainless steel;
表面机械研磨处理对316L不锈钢组织和性能的影响
补充资料:B301涂料蓝MFG
分子式:
CAS号:
性质:蓝色浆状。具有涂料色浆的通性。有良好的染色、印花性能。由4303稳定型酞菁蓝BS、平平加和甘油经调和磨细后,以水稀释而成。适于以直接印花或同浆印花的工艺。用于涂料印花和塑料薄膜的印花。
CAS号:
性质:蓝色浆状。具有涂料色浆的通性。有良好的染色、印花性能。由4303稳定型酞菁蓝BS、平平加和甘油经调和磨细后,以水稀释而成。适于以直接印花或同浆印花的工艺。用于涂料印花和塑料薄膜的印花。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条