1) hydraulic feeding
液压给进
2) hydraulic
液压
1.
Constructional and Technical Features of Hydraulic Nine-roller Hot Plate Leveler in Shaogang;
韶钢全液压九辊热矫直机的结构和技术特点
2.
Improving of the Hydraulic System for Ladle Turntable;
钢包回转台液压系统改造
3.
The leak of the machine tool hydraulic system and solutions of it;
机床液压系统的泄漏与解决办法
3) hydraulic pressure
液压
1.
GK400N mixer hydraulic pressure and lubrication system analysis;
GK400N密炼机液压和润滑系统分析
2.
Y3180H gear-hobbing machine hydraulic pressure principle of work and fault analysis;
Y3180H型滚齿机液压工作原理和故障分析
3.
Design of round wood non-center peeling machine based on thickness detecting and hydraulic pressure;
基于测厚控制与液压的无卡轴旋切机设计
4) hydraulic system
液压
1.
Study on the Arm Structure and Hydraulic System of Intelligent Bridge_detection Vehicle;
智能桥梁检测车臂架结构及液压系统的研究
2.
The design means of the hydraulic system and the circuitry were introduced .
文章给出了旋转升降舞台总体设计思路,详细介绍了液压系统、电气控制系统设计方案,以及该液压系统的一例典型故障的诊断与维修过程。
3.
This paper analyzes the working processes of hydraulic and mechanical driving systems in caterpillar combines and focuses on the configuration method of the hydraulic driving system, the selection of the hydraulic components, the specification of the hydraulic system, the calculation and testing of the performance of the hydraulic system in some combines.
液压行走系统因其结构简单、操纵方便、转向灵活等特点已广泛在联合收割机中采用。
5) hydraulic transmission
液压
1.
Method In ordinary traction beds designed by mechanical－ electrical－ microprocessor controlling method,this paper put a new method useing hydraulic transmission.
方法应用液压传动技术、采用计算机专家系统控制的方法。
6) hydraulics
液压
1.
The CAT Improvement on CSP Line Hydraulics Testing Stand;
CSP生产线液压实验台CAT改进
2.
To design electromotor seat which can be moved by x-axis or y- a xis for dragging the five ton s electromotor and eliminating anti-influence ca used by dragon crane, the paper studied on this subject and made designing wor k for achieving the goal which could realize automation through the close combin ation of machinery and hydraulics and electronics.
为此,进行了这方面的方案研究,并进行了设计开发,通过机械、液压、电气三个方面的紧密结合,能够实现自动控制。
3.
This paper presents an intelligent coiling machine with advanced skills of machine,electric,hydraulics,electron and computer designed for manufacting motor windings with thick flat wires.
针对扁平线以宽边为绕制方向绕制电机线圈的要求,提出了一种集机械、电气、液压、电子、计算机等先进技术于一体的智能绕线机。
参考词条
补充资料：缓进给磨削
用减小进给量、加大磨削深度的办法提高金属切除率的高效率磨削。一般在特制的卧轴平面磨床上，用砂轮周边以大的切削深度 (е=1～20毫米)和慢的进给速度（vW＝10～300毫米/分）进行平面或成形磨削(见图)，砂轮线速度v＝30米／秒左右。缓进给磨削适合于加工各种成形表面和沟槽，特别是淬硬钢和高温合金等高硬度、高强度的难加工金属材料的工件，如燃气透平叶片榫齿等。用这种方法可以从工件毛坯直接磨出所要求的表面形状和尺寸，既能提高效率，又能保证加工质量。由于磨削深度大，砂轮与工件的接触弧长比普通磨削大几倍至几十倍，磨削力、磨削功率和磨削热大幅度增加，故要求机床刚度好、功率大，并设有高压大流量的切削液喷射冷却系统,以便有效地冷却工件，冲走磨屑。缓进给磨削大多采用陶瓷结合剂的大气孔、松组织的超软普通磨料砂轮，以保证良好的自锐性、足够的容屑空间和避免工件表面烧伤；也可采用聚氨脂树脂结合剂砂轮或超硬磨料砂轮。这种磨削的加工效率可比普通磨削高1～5倍, 磨削精度可达2～5微米，表面粗糙度达Ra1.25～0.16微米。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。