1) S-157 phenolic resin
S-157酚醛树脂
1.
Carbon fiber reinforced S-157 phenolic resin is an antiablative heat shielding compoiste.
利用热重分析法对碳纤维增强S-157酚醛树脂在氮气和空气气氛下的热降解过程进行分析,研究了热降解气氛、升温速率与材料热降解温度、残炭率之间的关系,以及对其烧蚀性能的影响,并求得该复合材料的热降解活化能,分析其热降解机理,为烧蚀防热复合材料的热性能评价提供一种研究方法。
2) S-15X phenolic resin
S-15X酚醛树脂
1.
Curing process,thermal loss,molecular weight and molecular weight distribution of Boron-phenolic resin and S-15X phenolic resin are characterized and compared by DSC,TG and GPC.
本文采用DSC、TG和GPC等测试方法对硼酚醛树脂和S-15X酚醛树脂的固化工艺、热失重特性、分子量及其分布进行了表征和对比,在此基础上对比研究了连续玄武岩纤维、S-2高强玻璃纤维、高硅氧纤维、碳纤维增强硼酚醛树脂和S-15X酚醛树脂复合材料的烧蚀性能和弯曲性能,最后考察了脱模剂对硼酚醛树脂复合材料压制工艺的影响。
3) phenolic resin
酚醛树脂
1.
Preparation of porous carbon foams using phenolic resin as precursor;
酚醛树脂为前驱体制备多孔碳泡沫材料
2.
Synthesis and characterize a new type highly-heat-resistant phenolic resin;
一种高耐热酚醛树脂的合成及表征
3.
Synthesis and properties of boron-and-silicon-containing phenolic resin;
硼硅双改性酚醛树脂的合成与性能
4) PF resin
酚醛树脂
1.
The development of wood PF resin adhesive;
木材工业用酚醛树脂胶粘剂的现状及研究进展
2.
Special PF Resin for Light-alloy Coated Sand;
轻合金覆膜砂专用酚醛树脂的开发研究
3.
Using pyrolytic tar from larch bark as partial substitute for phenol in proportions of 0%, 20%, 40%, 60% , four types of PF resins were prepared and applied in hot-pressing three- layer poplar plywood by orthogonal test methods with different levels of press pressure, press time, and and resin content.
以落叶松树皮热解油按比例0%、20%、40%、60%代替苯酚制备的4种酚醛树脂胶黏剂和人工林杨木单板为原料,采用正交实验设计方法,选择不同的热压压力、热压时间和涂胶量进行了3层胶合板压制试验。
5) phenol-formaldehyde resin
酚醛树脂
1.
Investigation on curing mechanism of phenylphenol modified phenol-formaldehyde resin by means of DSC method;
DSC对苯基苯酚改性酚醛树脂固化机理研究
2.
Preparation of water-soluble low hydroformylation phenol-formaldehyde resin;
一种低甲醛含量水溶性酚醛树脂的制备
3.
Preparation of phenol-formaldehyde resin/graphite bipolar plate conductive composite of high properties;
高性能酚醛树脂/石墨双极板导电复合材料的制备
6) phenol resin
酚醛树脂
1.
Synthesis of the phenol resin modified with an aniline derivative;
苯胺衍生物改性酚醛树脂的研制
2.
Study on Mechanical Properties of OMMT Modified Epoxy/Phenol Resin;
有机改性蒙脱土增强环氧/酚醛树脂力学性能研究
3.
The multi-walled carbon nanotubes(MWNTs) is easy dispersing in the phenol resin because of a great number of phenyl groups and hydroxy groups in the phenol resin.
本文研究了多壁碳纳米管(MWNTs)在热固性钡酚醛树脂中的分散效果以及碳纳米管对酚醛树脂固化和炭化的影响。
补充资料:2401纯酚醛树脂
2401树脂是由烷基苯酚和甲醛在碱性介质下缩聚而制得。有优良的耐热性、耐磨性、耐水性和耐老化性等。溶于苯、甲苯、醋酸乙酯、溶剂汽油、环己烷等有机溶剂和植物油。240l树脂的质量规格与2402完全相同。与氯丁橡胶和丁腈橡胶有良好的相容性。
外观 黄色至棕红色透明块状固体
软化点(环球法) 80-110 ℃
油溶性(树脂:桐油=1:2) 全溶
用作氯丁胶粘剂的增粘树脂,以该树脂配制的氯丁溶剂型胶粘剂,粘接铝帆布的剥离强度达4kN/m。还可用作压敏胶的增粘剂、丁基橡胶的硫化剂等。贮存于阴凉、通风的库房内,远离火种、热源。
外观 黄色至棕红色透明块状固体
软化点(环球法) 80-110 ℃
油溶性(树脂:桐油=1:2) 全溶
用作氯丁胶粘剂的增粘树脂,以该树脂配制的氯丁溶剂型胶粘剂,粘接铝帆布的剥离强度达4kN/m。还可用作压敏胶的增粘剂、丁基橡胶的硫化剂等。贮存于阴凉、通风的库房内,远离火种、热源。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条