1)  RTM
树脂传递模塑成型
1.
The dependence of performance of RTM 6421 bismaleimide resin (BMI) on storage life at room temperature and low temperature was studied.
主要研究了树脂传递模塑成型(RTM)用6421双马来酰亚胺(BMI)树脂在室温和低温两种不同储存条件下长期储存后的性能对时间的依赖性。
2)  Advanced composite
树脂传递模塑成型（RTM）
3)  resin
树脂
1.
Study on adsorption dynamics of cephalosporin C in adsorption resin;
大孔吸附树脂对头孢菌素C的吸附动力学研究
2.
Study on adsorption of hexanal included in cyclohexanone with cation exchange resin;
树脂吸附环己酮中己醛的研究
3.
Application of Chemical Modification of Biomass in Resin Technology;
生物质化学改性在树脂化技术中的应用
4)  pitch
树脂
1.
In this paper,the properties of pitch and deposit in pulp were introduced,as well as its harm and the way of wet-end control,in order to provide theory support to the effective pitch control in the mills.
介绍了树脂及其沉积物的来源和种类、物理和化学特性、危害及其主要的湿部控制方法,为实际生产中解决树脂障碍提供了有效的理论基础。
2.
In order to evaluate the capability of lignin degradation and pitch elimination from Masson pine chips by nature white-rot fungi,20 white-rot fungus strains were obtained by petri dishes screening and petri dishes color-reaction screening.
为评价从野外筛选得到的白腐菌对造纸原料马尾松的木素降解和树脂脱除能力,将带菌样本经室内平板初筛及平板变色反应复筛,得到了20株纯白腐菌菌株,并对变色系数最小的一株菌株G进行松木片固体接种试验,测定3、5、7、9天后松木片的木素、树脂降解情况。
3.
The degradation rates of lignin and pitch were determined after 3 days,5 days,7 days and 9 days respectively.
测定经2种不同浓度无机盐稀释的菌悬液接种松木片3天、5天、7天、9天后的木素、树脂降解情况。
5)  Colophony
树脂
1.
Use colophony to absorb and remove the organics in the industrial hydrogen peroxide ,then, add stabilizer to remove inorganic impurities, so the quality of product can reach the standard of electronic grade.
用工业双氧水先经树脂吸附脱去其中的有机物,再添加稳定剂除去无机杂质,生产的产品可达到电子级产品的标准。
6)  resins
树脂
1.
Isolation and purification of proanthcyanidins from sea buckthorn seed by resins;
树脂法精制沙棘籽原花色素的研究
2.
A study on extraction and isolation of total flavonoids from Elaeagnus mollis leaves by macroporous absorptive resins;
大孔吸附树脂提取分离翅果油树叶总黄酮的研究
3.
Relationship of New-type AgriculturaI Films between Resins, Additives and Processing Qualities;
农用新型薄膜与树脂、助剂、加工质量的关系
参考词条
补充资料：传递模塑
    　　制造热固性塑料制品常用的塑料加工方法，也用于橡胶加工。热固性塑料或橡胶料（可以先行预热）在加料室内加热、熔融（图a）,再在加压下进入加热的闭合型腔内（图b）,经过固化后（或硫化），脱模即得制品。
　　
　　传递模塑与模压相仿，都借助于压机，但又有注射成型的特点，模具设有浇口和流道。
　　
　　这种方法要求热固性塑料，在未达到固化温度以前具有较大的流动性，而达到固化温度后又具有较快的固化速率，如酚醛树脂、三聚氰胺－甲醛树脂和环氧树脂等。用于橡胶制品加工时，胶料必须流动性好，硫化快。此法与模压相比，其优点是固化较均匀,生产周期短,尺寸精确度好，飞边修饰较易，嵌件和芯子不易变形，特别适于生产镶嵌件的制品。缺点是模具费用较大，模腔、浇口、流道中剩余料无法回收，故原材料单耗稍高。
　　

说明：补充资料仅用于学习参考，请勿用于其它任何用途。