1) continuous ohmic heating
连续通电加热
1.
Electrical conductivity of soybean milk during cooking with continuous ohmic heating device;
连续通电加热条件下豆浆的电导率
2.
Temperature distributing of tap water was studied with a self-designed minitype continuous ohmic heating device.
利用自行研制的小型液态食品通电加热装置研究了自来水在连续通电加热过程中的温度分布。
2) continuous heating
连续加热
1.
By comparing the starting line of continuous heating transformation with that of TTT diagram, the similarity and difference of the microstructure instability during continuous heating and isothermal heating co.
通过比较连续加热与等温加热条件下的相转变开始线,探讨了连续加热与等温加热条件下结构失稳机制的异同。
2.
The law and characteristics of 7Cr7Mo3V2Si steel under the condition of continuous heating have been studied systematically by using an advanced fully automatic transformation determining instrument called Formaster.
利用Ｆｏｒｍａｓｔｏｒ全自动相变测定仪研究了７Ｃｒ７Ｍｏ３Ｖ２Ｓｉ钢在连续加热条件下的相变规律及特点；测定了能反映其相变规律与特点的奥氏体形成图。
3) electric heating flexible continuous sucker rod
电加热柔性连续抽油杆
1.
Computer simulation for dynamic characteristics of electric heating flexible continuous sucker rod;
电加热柔性连续抽油杆动态特性的计算机模拟
2.
Analysis of the Dynamic Characteristics for Electric Heating Flexible Continuous Sucker Rod;
电加热柔性连续抽油杆动态特性分析
4) reheating furnace
连续加热炉
1.
An optimal study on the fuel consumption of reheating furnace;
中型轧钢厂连续加热炉各段供热优化研究
2.
Based on total heat exchange factor method,the online control process for reheating furnace was studied by simulation.
以总括热吸收率法为基础,对连续加热炉在线控制过程进行了软件仿真研究。
3.
By analyzing heat exchange in reheating furnace, a mathematician model of metal reheating process is established.
建立了炉内金属加热过程的数学模型,并以该模型为实验手段,对冶金企业连续加热炉的自寻最优控制进行了离线仿真。
5) continuous heating furnace
连续加热炉
1.
Analysis for continuous heating furnace of the nonlinear fusion in the running state;
连续加热炉运行状态非线性融合分析
2.
Neural network fusion analysis of the running states for continuous heating furnace;
连续加热炉运行状态神经网络融合分析
3.
This paper evaluates the application effects and problems that multicrystal mullite refractory fabrics be sticked to the inner linings of continuous heating furnace through thermal measure and calculation.
通过热工测试与计算 ,评价了多晶莫来石耐火纤维在连续加热炉上的应用效果及问
6) continuous reheating
连续再加热
补充资料：钢锭连续加热
钢锭连续加热
continuous reheating of ingot
gangding lionxu Jiare钢锭连续加热(eontinuous:eheating。f in-got)在连续式加热炉(见加热炉)中进行的钢铰加热。一般采用多段式(3~5段)连续加热炉(见图)。在特殊钢厂应用较多，以加热合金钢冷锭为主。用多段式加热的目的是易于控制每段的炉温，以适应特殊成分的钢枕的加热要求。也可用以加热碳钢小钢锭及大连铸坯。加热温度规范(见钢锐加热)主要根据钢的性质、化学成分和工艺要求而定。 口罐鬓瓢 多段式连续加热炉 (王允禧)
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条