1) Out-of-campus Corresponding School
教学点
1.
About Supervision on Teaching Quality of Adult Academic Education in Out-of-campus Corresponding Schools;
成人高等学历教育校外教学点办学质量的监控
2) teaching characteristics
教学特点
1.
On the teaching characteristics of classical academy and its practical significance;
论书院的教学特点及其现实意义
2.
This article discusses the teaching characteristics of lathe work practice elective course,pnts forward the focal points,the test its way and standards and probes into the teaching of lathe work practice elective course.
本文通过对高职车工实习选修课教学特点的总结和分析,提出车工实习选修课教学的重点,改进了实习成绩考核办法和标准,对车工实习选修课教学进行了有益的探索。
4) teaching characteristic
教学特点
1.
According to the teaching characteristic and market demand of higher vocational colleges,the author develops the Automobile Field Courses based on graduations work.
文中探讨和讲述了根据高职教育的教学特点和市场需求,以就业为导向开发汽车运用技术专业的专业课程。
2.
According to the teaching characteristic of quality education;this paper expatiates the course content,the teaching method and practical teaching in detail to construct the course of Automobile Engine Structure and Overhaul.
文中根据高职教育的教学特点,从教学内容、教学手段和实训教学三个方面详细阐述了高职类《汽车发动机构造与检修》课程的构建。
3.
This paper describes the historical origin of Taiji and its teaching characteristic in order to make learners understand Taiji,make the teaching of taiji more normal and the movements more standard.
文章就太极拳的历史渊源及教学特点进行了论述,旨在使学习者对太极拳更为了解,使太极拳的教学更为规范,动作更为标准,体现中华武术的魅力所在,弘扬中华文化。
6) Teaching Emphasis
教学重点
1.
The Teaching Emphasis of Residential Environmental Design;
“居住小区环境设计”教学重点浅析
补充资料:闭式单点、双点压力机
| |||||||
主要参数内容 | 国际先进 | 国内先进 | 国内一般 | 国内落后 | 评定方法及说明 | ||
(一)加工精度 | 参照GB10924-89、GB10933-89、JB5200-91 | ||||||
1、滑块下平面对工作台上平面的平行度(mm) | 30%精度储备 | 20%精度储备 | 达到规定值 | 大于规定值 | |||
0.02+0.10/100×滑块下平面的被测长度 | |||||||
2、滑块行程对工作台上平面的垂直度 | 30%精度储备 | 20%精度储备 | 达到规定值 | 大于规定值 | |||
0.05+0.02/100×滑块行程长度 | |||||||
(二)结构性能 | |||||||
1、离合器、制动器接通率,当滑块行程次数≤16次/分时为70%,≤25次/分时为60%,≤45次/分时为50% | 大于规定值10% | 大于规定值 | 达到规定值 | 达不到规定值 | |||
2、液压超负荷保险装置、微调装置、吨位指示器 | 全部具有 | 全部具有 | 部分具有 | 没有 | |||
(三)噪声dB(A) | |||||||
1、公称力≤400kN | ≤85 | ≤87 | ≤88 | >88 | |||
2、公称力>400kN | ≤87 | ≤88 | ≤90 | >90 |
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条