1) alumina ceramics Laser pump cavity
![点击朗读](/dictall/images/read.gif)
氧化铝陶瓷激光泵浦腔
2) Alumina ceramics
![点击朗读](/dictall/images/read.gif)
氧化铝陶瓷
1.
Effects of sintering temperature on fatigue damage of alumina ceramics;
![点击朗读](/dictall/images/read.gif)
烧结温度对氧化铝陶瓷疲劳损伤过程的影响
2.
Quantitatively research of fatigue damage of alumina ceramics;
![点击朗读](/dictall/images/read.gif)
氧化铝陶瓷疲劳损伤过程的数字描述
3.
Application of steel-alumina ceramics composite pipe for dilute phase pneumatic conveying;
氧化铝陶瓷内衬复合钢管在稀相气力输送中的应用
3) alumina
[英][ə'lu:mɪnə] [美][ə'lumɪnə]
![点击朗读](/dictall/images/read.gif)
氧化铝陶瓷
1.
Dynamic behaviors of alumina ceramic under high pressure and high strain-rate;
![点击朗读](/dictall/images/read.gif)
氧化铝陶瓷在高压高率条件下动态特性
2.
Experimental study on shear response of alumina under combined compression and shear loading;
压剪复合冲击下氧化铝陶瓷的剪切响应实验研究
3.
The effect of different impurities and dopants on the dielectric loss of alumina ceramics are reviewed.
综述了不同杂质及掺杂对氧化铝陶瓷介电损耗影响的研究进展。
4) alumina ceramic
![点击朗读](/dictall/images/read.gif)
氧化铝陶瓷
1.
Effects of nano-silica coating on microtensile bond strength of glass infiltrated alumina ceramic;
纳米硅涂层对玻璃渗透氧化铝陶瓷粘结强度的影响
2.
Mechanical properties of brazing joint of alumina ceramics to mild steel
![点击朗读](/dictall/images/read.gif)
氧化铝陶瓷与低碳钢钎焊接头的力学性能
3.
Vacuum flashover developing across alumina ceramic at pulsed voltage
![点击朗读](/dictall/images/read.gif)
真空冲击电压下氧化铝陶瓷沿面闪络现象的发展过程
5) Al2O3 ceramics
![点击朗读](/dictall/images/read.gif)
氧化铝陶瓷
1.
The research developed the high temperature glaze suitable for Al2O3 ceramics in metallized process under 1450℃.
本文总结并实验对比了国内外的几种高温釉,从而提出釉料化学性质、釉料中氧化铁等变价元素以及原料矿物组成是导致氢烧釉面失光的主要因素,并成功试制出适宜于氧化铝陶瓷以及1450℃金属化工艺的高温釉。
2.
Al2O3 ceramics were successfully superfast densified by spark plasma sintering (SPS) underthe conditions of heating rate as high as 600℃/min, no holding time at the sintering temperaturefrom 1350 to 1700 ℃ and then fast cooling to 600℃ within 3 minutes.
本文介绍用放电等离子超快速烧结方法制备的氧化铝陶瓷的力学性能和显微结构特征。
6) ceramic alumina
![点击朗读](/dictall/images/read.gif)
陶瓷氧化铝
补充资料:半导体激光泵浦的激光晶体
半导体激光泵浦的激光晶体
LD pumped laser crystal
半导体激光泵浦的激光晶体LD PumPed lasercrystal适用于半导体二极管作泵浦源的激光晶体。传统的固体激光器一般用闪光灯泵浦,由于闪光灯的发光区域宽,只有一部分能量被吸收后转换成激光,大部分转换成热量,使工作物质温度上升,恶化了输出激光束的质量。半导体激光器输出的激光谱线窄(一般为几纳米),选择合适的半导体激光器,使其激光光谱与某种固体激光材料的吸收光谱匹配,即可达到高效泵浦,大大减轻固体工作物质的热负荷。 因为半导体激光器光泵区域小,需用的晶体尺寸也小,因此要求基质晶体内可掺入的激活离子浓度要高,且不产生浓度碎灭。此外,要求与光泵的半导体激光波长相匹配的晶体的吸收带要宽,吸收系数要大;要有低的阑值功率;Q开关运转时,荧光寿命要长。当泵浦光源从闪光灯改变为半导体激光二极管时,对被泵浦的激光晶体产生了不同的要求。用闪光灯泵浦时,对材料的热性能和机械性能有严格要求,而半导体泵浦则更注重材料的光谱性能。 在已使用的激光晶体中,掺钱石榴石(Nd:YAG)晶体的阑值功率低,光学质量高,是应用于半导体激光光泵的固体激光器的主要材料。由于Nd3+离子在基质晶体中受分凝系数的限制,Nd3+离子浓度不能太高,所以一些氟化物和钨、钥酸盐晶体等掺杂浓度高,激光效率高,荧光寿命长,有可能成为半导体激光泵浦的后选晶体。 用半导体泵浦可制成效率高、功率和频率稳定、激光束质量好、寿命长的全固化激光器,并经各种频率转换技术,可发展成各种波长、各种模式、各种运转方式的激光器,这种激光器将在很大范围内取代已有的各类固体、液体和气体激光器。 (沈鸿元)
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条