1) Two-parameter Lvy's area
![点击朗读](/dictall/images/read.gif)
二参数Lvy区域
3) Lévy's area with two-parameter
![点击朗读](/dictall/images/read.gif)
二参数Lévy区域
4) Levy's area with two-parameter
![点击朗读](/dictall/images/read.gif)
二参数Levy区域
5) parametric variation region
![点击朗读](/dictall/images/read.gif)
参数区域
1.
By the discussion of parametric variation region under the condition of stability null solution for two-dimension overlay linear differential systems, we obtain some theorems to tell us how to get the parametric variation region of n -dimension linear or nonlinear autonomous differential systems that the null solution is stable.
通过对二维叠加线性微分系统零解稳定条件下参数区域变化情况的讨论,给出了在n维叠加线性及非线性微分系统零解稳定条件下可以得到参数的变化区域;举例说明参数变化区域的大小与所作的李雅普诺夫函数有关;并且说明可以通过改进所给系统的李雅普诺夫函数来扩大参数的变化区域。
6) regional parameters
![点击朗读](/dictall/images/read.gif)
区域参数
1.
The approach to develop a ground motion attenuation relation in a country or region with no enough observed data is deal with by means of seismological method in this paper, and mainly on the estimation of regional parameters.
反演结果,与加州以前发表的区域参数研究成果大体上相符。
补充资料:聚对苯二甲酸乙二(醇)酯(PET)塑料的注塑工艺参数
料筒温度 喂料区 50~70℃(70℃)
区1 240~260℃(250℃)
区2 240~260℃(250℃)
区3 250~290℃(270℃)
区4 250~290℃(270℃)
区5 250~290℃(270℃)
喷嘴 250~290℃(270℃)
括号内的温度建议作为基本设定值,行程利用率为35%和65%,模件流长与壁厚之比为50:1到100:1
熔料温度 270~280℃
料筒恒温 220℃
模具温度 120~140℃
注射压力 薄截面制品可达160MPa(1600bar)
保压压力 大约注射压力的50%~70%以避免产生缩壁;按需选择保压时间;太长的保压时间易造成内应力,特别是对非晶体树脂,会使产品的抗冲击性降低
背压 5~10MPa(50~100bar),避免产生摩擦热
注射速度 因为高固化率和结晶率故需采用高速;避免在注射过程中熔料冷却和凝结;模内保持良好的通气性是很重要的,否则裹入的空气易使流道末端产生焦化
螺杆转速 最大螺杆转速折合线速度为0.5m/s
计量行程 (0.5~3.5)D,因为熔料对过热和在料筒内残留时间过长很敏感;残留时间不应超过5min
残料量 2~5mm,取决于计量行程和螺杆直径
预烘干 在120℃时烘干4h
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条