|
|
1) Sediment earthquake cross section
沉积物地震剖面
2) sediment profile
沉积物剖面
1.
Samples from 18 sediment profiles (0 to 60 cm) under 3 dominated plants (Phragmites australis, Cyperus malacceusis and Scirpus triqueter) in 2 different districts far and near a tide ditch in the middle of the Shanyutan wetland were collected.
以闽江河口最大的鳝鱼滩湿地为研究区,选择远、近潮沟2个不同潮水水淹区域设置样线,对研究区3种建群植物芦苇(Phragmites australis)、短叶茳芏(又称咸草)(Cyperus malacceusis)和藨草(Scirpus triqueter)下18个沉积物剖面分层取样,研究闽江河口湿地远、近潮沟区不同植物下沉积物有机碳含量和储量的垂直分布特征。
3) sedimentary profile
沉积剖面
1.
We discussed the whole characteristics and main affect factor of lacustrine sedimentary profile of ~(137)Cs in five lake areas by reason of different physiognomy.
研究表明:影响~(137)Cs沉积剖面分布的因素,除了纬度和海拔外,还应与当地的地貌特征、降雨量、植被状况和人类活动有关;全球核大气沉降是中国湖泊沉积物的~(137)Cs剖面分布最主要的来源,同时我国早期的大气核试验和前苏联切尔诺贝利核泄漏事件对我国部分地区~(137)Cs分布可能有一定的影响。
4) seismic profile
地震剖面
1.
Geological interpretation of the seismic profile in Tarim Basin and tectonic evolution of this area
塔里木盆地地震剖面地质解释及其构造演化
2.
Demarcating through-well seismic profile with diplog is one of the important ways to improve the quality of seismic interpretation.
地层倾角测井标定过井地震剖面是提高地震成果质量的重要途径之一。
3.
In seismic description,it often traced geologic horizon in seismic profile and reflected the geologic information on corresponding seismic horizon.
在地震解释中,常常在地震剖面上追踪地质层位,并且将地质信息映射到相应的地震层位上,有时追踪某一地震层位的波峰,有时是波谷,多数时候都没能精确地确定地质层位的位置。
5) seismic section
地震剖面
1.
Fault analysis and fault correlation in seismic section;
地震剖面上的断层分析及相关意义
2.
Lithology prediction of 2-D seismic section by neural net work technique;
用神经网络预测二维地震剖面的地层岩性
3.
Application research of digital image processing method for improving signal to noise ratio of seismic section image;
利用数字图像处理技术提高地震剖面图像信噪比
6) seism facies section
地震相剖面
补充资料：关于solidworks 中的剖面线中的剖面线
solidworks的剖面线线型定义和autocad相同,它使用了autocad的剖面线定义方法,与autocad通用.因此,可以对剖面线进行定义. 方法:修改\SolidWorks\lang\chinese-simplified\sldwks.prn 用笔记本打开该文件,添加需要的线形.如 ;; Based on AutoCAD Ver.13.0s Hatch Pattern File ;;;; solidworks 区域剖面线定义文件 :: *金属, (Iron BrickStone), ANSI Iron, Brick, Stone masonry 45, 0,0, 0,.125 *塑料, (Lead Zinc Mg), ANSI Lead, Zinc, Magnesium, Sound/Heat/Elec Insulation 45, 0,0, 0,.125 135, 0,0, 0,.125 *玻璃,AR-GLASS@1.0 45,0,0,0,0.5, 0.5,-0.5 45,0,0.1414214, 0,0.5, 0.3,-0.7 45,0.1414214,0, 0,0.5, 0.3,-0.7 *软木, Cork material@1.0 0, 0,0, 0,.125 135, .0625,-.0625, 0,.35355339, .176776696,-.176776696 135, .09375,-.0625, 0,.35355339, .176776696,-.176776696 135, .125,-.0625, 0,.35355339, .176776696,-.176776696 *无, None 删除不需要的定义类型,可以大大提高solidworks 的启动速度
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条
|