|
|
1) Wave power deposit profile
功率沉积剖面
2) sedimentary profile
沉积剖面
1.
We discussed the whole characteristics and main affect factor of lacustrine sedimentary profile of ~(137)Cs in five lake areas by reason of different physiognomy.
研究表明:影响~(137)Cs沉积剖面分布的因素,除了纬度和海拔外,还应与当地的地貌特征、降雨量、植被状况和人类活动有关;全球核大气沉降是中国湖泊沉积物的~(137)Cs剖面分布最主要的来源,同时我国早期的大气核试验和前苏联切尔诺贝利核泄漏事件对我国部分地区~(137)Cs分布可能有一定的影响。
3) sediment profile
沉积物剖面
1.
Samples from 18 sediment profiles (0 to 60 cm) under 3 dominated plants (Phragmites australis, Cyperus malacceusis and Scirpus triqueter) in 2 different districts far and near a tide ditch in the middle of the Shanyutan wetland were collected.
以闽江河口最大的鳝鱼滩湿地为研究区,选择远、近潮沟2个不同潮水水淹区域设置样线,对研究区3种建群植物芦苇(Phragmites australis)、短叶茳芏(又称咸草)(Cyperus malacceusis)和藨草(Scirpus triqueter)下18个沉积物剖面分层取样,研究闽江河口湿地远、近潮沟区不同植物下沉积物有机碳含量和储量的垂直分布特征。
4) Power deposition
功率沉积
1.
Power deposition of electron cyclotron waves in hot plasmas;
电子回旋波在热等离子体中的功率沉积
2.
Ray tracing method is used to calculate and superpose the power deposition of any wave packet, and the power deposition result is obtained.
用射线轨迹方法计算并叠加每一波束功率沉积 ,得到快波功率沉积的计算结果 。
3.
In this paper, the propagation of fast waves in the ion-cyclotron range of frequencies, the current drive and the power deposition in plasmas are investigated, some important results are as follows.
本文对离子回旋频段的快波在等离子体中的传播以及快波在等离子体中的功率沉积、驱动起的电流等进行了研究和计算,并得到了如下若干重要结论。
5) deposition power
沉积功率
1.
48O 3(PZT) ferroelectric thin films were deposited on LaNiO 3 coated p-Si(111) substrates by RF magnetron sputtering at low substrate temperature( T =370℃) with deposition power ranging from 60W to 120W, sequentially followed by a rapid thermal annealing(RTA) process at temperature 650℃ for 5 minutes.
结果表明 ,PZT薄膜的组分、结构和性能都与溅射沉积功率有
6) fluvial sediment profile
河流沉积剖面
补充资料：关于solidworks 中的剖面线中的剖面线
solidworks的剖面线线型定义和autocad相同,它使用了autocad的剖面线定义方法,与autocad通用.因此,可以对剖面线进行定义. 方法:修改\SolidWorks\lang\chinese-simplified\sldwks.prn 用笔记本打开该文件,添加需要的线形.如 ;; Based on AutoCAD Ver.13.0s Hatch Pattern File ;;;; solidworks 区域剖面线定义文件 :: *金属, (Iron BrickStone), ANSI Iron, Brick, Stone masonry 45, 0,0, 0,.125 *塑料, (Lead Zinc Mg), ANSI Lead, Zinc, Magnesium, Sound/Heat/Elec Insulation 45, 0,0, 0,.125 135, 0,0, 0,.125 *玻璃,AR-GLASS@1.0 45,0,0,0,0.5, 0.5,-0.5 45,0,0.1414214, 0,0.5, 0.3,-0.7 45,0.1414214,0, 0,0.5, 0.3,-0.7 *软木, Cork material@1.0 0, 0,0, 0,.125 135, .0625,-.0625, 0,.35355339, .176776696,-.176776696 135, .09375,-.0625, 0,.35355339, .176776696,-.176776696 135, .125,-.0625, 0,.35355339, .176776696,-.176776696 *无, None 删除不需要的定义类型,可以大大提高solidworks 的启动速度
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条
|