说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 糙点
1)  coarse point
糙点
2)  slugs [英][slʌg]  [美][slʌg]
3)  brown rice
糙米
1.
Study on effect of moisture condition for brown rice on mechanical characteristic;
糙米加湿调质工艺参数对其力学指标影响规律的研究
2.
Effect of moisture conditioning treatment of brown rice on the water absorption rate of polished rice based on isotope tracing;
基于同位素示踪技术的糙米加湿后精米吸水率的试验研究
3.
Effect of moisture conditioning treatment on milling characteristic of brown rice;
糙米加湿调质对其碾米性能影响的试验研究
4)  Phlomis umbrosa turcz
糙苏
1.
[Objective] To study the chemical constituents of the leaves and tender branches of wild Phlomis umbrosa Turcz obtained from Qinba Mountain,This research will provide scientific proof and empolder this natural resource.
[目的]研究秦巴山区野生的糙苏叶和嫩枝中的化学成分,为开发这一野生资源提供科学依据。
5)  unpolished rice
糙米
1.
Production craft of microporous starch prepared with unpolished rice as raw material were studied.
研究以糙米为原料制备多孔淀粉的生产工艺。
2.
The Oolong tea was infused and centrifuged to make tea brew; The unpolished rice was baked, smashed, dextrinized, enzymic degradated and centrifuged to make rice water.
乌龙茶浸提后离心制得茶汤;糙米经过烘烤、粉碎、糊化后酶解、离心后取其上清液得米汤,然后将米汤和茶汤以一定比例混合,并添加一定的配料而研制成一种既营养又符合消费者口味的健康饮料。
3.
A multiresidue method based on gel permeation chromatography (GPC) clean-up and gas chromatography-nitrogen-phosphorous detection (GC-NPD) was developed to detect 50 organophosphorous pesticide residues in unpolished rice simultaneously.
研究了同时检测糙米中50种有机磷农药残留的方法。
6)  Rough [英][rʌf]  [美][rʌf]
粗糙
1.
Wetting Behaviors of Ethanol/Water on Rough PTFE Surface;
粗糙PTFE涂层表面结构对乙醇/水混合溶液润湿性的影响
2.
We accordance with relevant provisions of the standard aluminum alloy profiles processed into standard samples, the high-frequency fatigue testing machine, the surface smooth and rough surface two groups in the same specimen under stress fatigue experiment.
按相关标准规定将铝合金型材加工成标准试样,在高频疲劳试验机上,分别对表面光滑和表面粗糙2组试样在相同应力作用下进行疲劳实验,并得出了2组试样的循环次数,结果表明表面粗糙试样循环次数显著低于表面光滑组试样。
补充资料:闭式单点、双点压力机
代码:00413
设备名称:闭式单点、双点压力机
型号规格:公称力≥800kN
计量单位:台
主要参数内容
国际先进国内先进国内一般国内落后评定方法及说明
(一)加工精度
    参照GB10924-89、GB10933-89、JB5200-91
1、滑块下平面对工作台上平面的平行度(mm)
30%精度储备20%精度储备达到规定值大于规定值 
0.02+0.10/100×滑块下平面的被测长度
     
2、滑块行程对工作台上平面的垂直度
30%精度储备20%精度储备达到规定值大于规定值 
0.05+0.02/100×滑块行程长度
     
(二)结构性能
     
1、离合器、制动器接通率,当滑块行程次数≤16次/分时为70%,≤25次/分时为60%,≤45次/分时为50%
大于规定值10%大于规定值达到规定值达不到规定值 
2、液压超负荷保险装置、微调装置、吨位指示器
全部具有全部具有部分具有没有 
(三)噪声dB(A)
     
1、公称力≤400kN
≤85≤87≤88>88 
2、公称力>400kN
≤87≤88≤90>90 
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条