说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 现代控制图
1)  Modern control block diagram
现代控制图
2)  modern control
现代控制
1.
The techniques in building linear transformation matrix in the modern control theory;
现代控制理论中线性变换矩阵的构造方法
2.
Its stability is a typical problem to the application of modern control theory.
倒立摆系统是一个复杂的、非线性的、不稳定的高阶系统 倒立摆的稳定性控制是控制理论与应用的典型问题 本文从控制理论的发展过程出发 ,概述了经典控制理论、现代控制理论、人工智能控制理论以及拟人智能控制理论在倒立摆系统控制中的应
3)  cybernetics [英][,saɪbə'netɪks]  [美]['saɪbɚ'nɛtɪks]
现代控制论
4)  modern cybernetics
现代控制论
1.
The development from the classic cybernetics to the modern cybernetics experiences a great leap in people s recognition of the control techniques.
从经典控制论发展到现代控制论,是人类对控制技术认识上的一次飞跃。
2.
The development from classic cybernetics to modern cybernetics and intelligent cybernetics is a leap of human kind in the cognition of control technology.
从经典控制论发展到现代控制论、智能控制论是人类对控制技术认识上的飞跃。
3.
The development from the classic cybernetics to the modern cybernetics experiences a great leap in people s recognition of the control techniques.
从经典控制论发展到现代控制论,是人类对控制技术认识上的一次飞跃。
5)  modernization in quality control
质量控制现代化
6)  modern control theory
现代控制理论
1.
Research on analysis of SD model based on the modern control theory;
基于现代控制理论的SD模型解析研究
2.
Construction control of the large span spatial steel structure based on the modern control theory;
基于现代控制理论的大跨空间钢结构施工控制
3.
Design of the DC motor controller based on modern control theory
基于现代控制理论的直流电机控制器的设计
补充资料:不合格品率控制图(p图)


不合格品率控制图(p图)
control charts for fraction defective

  buhsgePinIO kongzhitu不合格品率控制图《p图)(cootrol chaztsfor俪ction de公兑tive)利用样本的一定类型的不合格品率(川,评估和监察过程的控制图,也是计数型控制图中最常用的控制图。计数数据往往能够快速而较便宜地取得,一般也不需要特别的收集技巧。计数型控制图的参数均值(产)与标准差(的是互相关的:例如,样本不合格品率(川的均值巧=p,标准差丐二石可下不下石,式中尸为过程或总体的平均不合格品率,。为样本大小。确定产,、凡中的一个就等于确定另一个,故只有一个独立的参数,即总体平均不合格品率p,因此,控制不合格品率(p)仅一张控制图就足够了。p图用于控制对象为不合格品率或合格品率等计件值的场合。常见的不良率有不合格品率、废品率、交货延迟率、缺勤率、差错率等。 p图的控制界限也是从休哈特控制图控制界限的总公式,即休哈特的3。方式导出的,具体如下:UCL二P+3_户,。丫六,一户,。CL二PoPLCL二P一3了P(l一P)/n了P(l一P)In。户一3丫户(:一户)/n式中:UCL为上控制限,比L为下控制线,CL为中心线,笋为总体平均不合格品率p的估计值,通常久。所有不合格品数厂“厂二一班看释魂礴「一 由于在p图的上下控制界限uCL、优L公式中含有样本大小n,故当n变化时,p图的上下控制界限呈凹凸状,不但作图难,而且更重要的是在p图上难于判断异常,也难于判断稳定。这时采用通用拉制图,可以克服上述困难。下页左图是一个实例的p图与不合格品数通用控制图(pn;图)的对比。(孙静)
  
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条