1) flatness and circularity
平整度及圆度
2) round
[英][raʊnd] [美][raund]
圆整度
1.
Methods The process was studied by a series of tests with the formations,the round and the weight deviation of Phenobarbital Pills as the evaluation quota to decide the best dropping condition, and the three factors were the temperature of mixture ,the dropping speed of drop pills and the formulation ingredients.
方法 通过对苯巴比妥滴丸制备过程的实验 ,以滴丸的成型、圆整度、重量差异为筛选指标 ,以药液的保温温度、滴制速度、药物与基质的最佳配比为主要考察因素 ,对苯巴比妥滴丸的制备工艺进行优选 ,并讨论了影响滴丸成型、圆整度及丸重差异的其他因素。
2.
Methods The process was studied by a series of tests with the formations,the round and the weight deviation of otic drop pills as the cvaluation quota to decide the best dropping condition, and the three factors were the temperature of mixture, the dropping speed of drop pills and the formulation ingredients .
方法 通过对氯霉素耳用滴丸制备过程的实验,以滴丸的成型,圆整度,重量差异为筛选指标,以药液的保温温度、滴制速度、药物与基质的最佳配比为主要考察因素,对氯霉素耳用滴丸的制备工艺进行优选。
3) roundness
[英]['raundnis] [美]['raʊndnɪs]
圆整度
1.
Methods:The process was studied by orthogonal experimental design with pill weight variation and roundness as the de- tective marker.
方法:采用正交实验法,以丸重差异和圆整度为考察指标,对影响清开灵滴丸滴制过程的因素进行考察。
2.
METHODS: A series of signal tests have been studied for the choice of substrate、 its proportion of substrate to drug、 the dropping and cooling agent temperature and dropping speed to make average pill weight,weight variation and roundness up to grade.
方法:以滴丸的平均丸重、变异系数和其圆整度等为评价指标,探讨了基质的选择,药物与基质的配比,滴制温度、滴速、滴距和冷凝液温度对滴丸成型性的影响。
3.
And more,optimization of abrasion resistance,roundness,mould service life,strength of bowling resistance,anti-breakage,high efficiency transfering is approached into on the basis of the above-said.
为了提高国产金属针布齿条的质量,运用产品设计的基本观点,对金属针布齿条设计进行归纳和分类,完整而详细地表述了产品设计的总体要求;在齿条外形轮廓及齿形参数设计中,强调了金属针布齿条结构区间及作用;并在此基础上从齿尖高耐磨、圆整度、冲模寿命、抗轧强度、防断裂、高效转移方面进行了优化设计的探讨。
4) Spherical degree
圆整度
1.
Methods Taking spherical degree and pill weight as index, the above factors were observed by orthogonal test.
方法 以滴丸圆整度和丸重为指标 ,采用正交设计试验法对影响因素进行考察。
5) average roundness
平均圆度
6) integral smoothness
整体平整度
补充资料：不圆度
不圆度
ovality
buyuandu不圆度(。vality)圆形金属材(包括棒、线、管等)横断面上最大与最小直径的差值，曾称作椭圆度。在产品标准上都规定有不圆度的允许偏差，一般约为直径正负偏差之和的。.5倍，圆管坯为直径公差的。.75一0.8倍，盘条直径则规定有绝对值0.24~0.6omm。钢管外径不圆度为直径偏差之和的。.5~1.0倍，钢丝不圆度则为直径偏差之和的0.5倍。 造成不圆的原因是:轧棍、锻追模具或冷拔模具的孔型不圆，塑性加工时孔型欠充满以及孔型错牙、导板和卫板安装不正或过松、轧件入孔型不正等。 (崔峰)
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条