1) critical work
临界功
1.
Since the surface tension value under a plane surface is too high and the calculated critical work to trigger nucleation is too low,the surface tension value under a concave surface has been quantitatively revised based on theoretical deductions and an assumption of a cubic molecular group.
针对均相核化率求解中存在对表面自由能数值估计过高和对核化临界功估算过大使核化率数值过低等问题,本文通过理论推导对表面自由能数值进行了定量修正,并提出了核化立方体微团的方法。
2) critical power
临界功率
1.
Nd:YAG CW laser heat-conduction welding——Ⅱ.calculation of critical power;
Nd:YAG CW激光热传导焊Ⅱ激光热传导焊临界功率的计算
2.
Then the Schrdinger-type nonlinear equation in strong nonlocality was given and from the equation the analytical expressions of the single soliton and the critical power .
得到了非线性系数以及特征长度和预倾角的关系,并且给出了强非局域性的非线性薛定谔方程,最终得到了单孤子和临界功率的解析解。
3.
In experiment,we observe the propagation of solitons in nematic liquid crystals,and determine the critical power of optical spatial solition in different beam width,for example,when the.
实验上,观察了空间光孤子在向列相液晶中的传输,找到了不同束宽下空间光孤子的临界功率。
3) critical pow er density
临界功率密度
4) critical power disturbance vectors
临界功率扰动向量
5) Critical onset temperature gradient
临界功产生温度梯度
6) Criticality
临界
1.
In the subcriticality range of 0 1$,the results ofαfrom different position are measured andαc can be extrapolated from theseα values.
用 BF3计数管作为探测器 ,采用时间延迟符合的测量方法 ,测量得出了实验室快临界装置在缓发临界时的瞬发中子衰减常数 αc,其值为 0 。
参考词条
补充资料:BCS临界温度`T_c`公式(formulaofBCScriticaltemperature$T_c$)
BCS临界温度`T_c`公式(formulaofBCScriticaltemperature$T_c$)
简称BCSTc公式。在弱耦合条件下所给Tc公式为:
`k_BT_c=(1.14)\hbar\omega_Dexp(-1//N(0)V)`
由此知Tc∝ωD,ωD为德拜频率。但$\omega_D\proptoM^{-1/2}$,M为同位素原子质量。实验指出,Tc∝M-α,对一般元素α=1/2。故上式给出了超导的同位素效应。实验结果又显示,当N(0)V≤0.2时,BCS理论结果与实验的符合很好;0.20<N(0)V<0.3时有1的误差;N(0)V>0.3时则误差增大较迅速。这里N(0)和V分别是T=0K时费米面上一种自旋取向的态密度和电子间净的有效吸引相互作用势强度。所以Tc受弱耦合($N(0)V\lt\lt1$)的限制,其最高Tc也受到限制,不能接近ωD的最高值所对应的Tc。BCS理论机制估计的最高Tc一般约30K左右,对金属氢估计可达252K。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。