1) Critical output
临界产量
1.
Through analyzing the effect of the vertical locations of horizontal wells on the critical output and gas breakthrough time of the gas cap reservoir, the curve showing the relationship between the vertical locations of horizontal wells and the critical output as well as the gas breakthrough time is obtained in t.
针对这一问题,从水平井垂向位置对气顶油藏临界产量和见气时间的影响入手,得出了临界产量和见气时间与水平井垂向位置的关系曲线;在综合考虑临界产量和见气时间的基础上,得到了水平井垂向位置与临界产量和见气时间乘积的关系曲线,由曲线趋势得到了气顶油藏水平井最优垂向位置的范围。
2.
The bottom water coning model used by Boyun Guo considered the influence of perforation length on critical output, so it can be used to calculate the perforation length of bottom water reservoir.
由于BoyunGuo等人使用的底水锥进模型引入了射孔长度对临界产量的影响,所以可用于优化底水油藏的射孔段长度。
3.
The paper has discussed the effect of vertical locations of horizontal wells on the critical output and producing pure oil time,analyzed the ratio .
水平井垂向位置与临界产量、产纯油时间、油水密度差和油气密度差比值,以及临界产量与产纯油时间的乘积等关系的研究结果表明,水平井垂向位置越靠近气顶或底水,临界产量越高,但产纯油时间越短;越靠近最佳位置(气水同时锥进到油井中),临界产量越低,产纯油时间越长。
2) critical production
临界产量
1.
The research and application of critical production model of fractures sand entry in fracturing gas well;
气井裂缝出砂临界产量模型研究及应用
2.
Then, the factors affecting production, critical production and water breakthrough time is studied an.
利用镜像反映及势函数的叠加原理 ,在获得底水油藏中任意一点的势函数后 ,得到了底水油藏中水平井底势差和水平井的产量方程 ,由此研究影响水平井产量、临界产量及见水时间的因素 ,通过研究获得了底水油藏中水平井的合理位置 ,为水平井开采底水油藏的优化设计提供了理论基
3.
In order to determine the suitable commissioning production, the critical production of bottom water coning must be studied.
QHD32 - 6油田A2 6水平井油层下有一底水 ,为了确定合理的投产产量 ,需要确定底水锥进的临界产量值。
3) critical production rate
临界产量
1.
Calculation method of critical production rate for fractured-vuggy reservoir with bottom water
塔河油田缝洞型底水油藏临界产量计算研究
2.
In 1993, a formula for critical production rate of oil well in bottom water reservoir with partition board was proposed by Dr.
1993年李传亮提出的带隔板底水油藏油井临界产量的计算公式中不含油井打开程度的参数,即没有考虑油井打开厚度的影响。
3.
On the basis of this theoretic model, the critical production rate, the shape of water coning and the optimum perforation intervals could .
在理论模型的基础上,建立了预测临界产量、水锥形态以及优化射孔长度的数学模型。
4) the formula of critical production rate
临界产量公式
5) critical velocity and volume
临界流速、产量
6) critical liquid-carrying rate
临界携液产量
1.
Aiming at the issue of correcting coefficient in gas well critical liquid-carrying rate calculation equation for gas liquid ration greater than 1400m3,on the basis of the liquid drop being flat-shaped in gas well bore and the relationship of drag coefficient and Reynolds number (between 1×103~2.
针对气液比大于1400m3/m3的气井临界携液产量计算公式存在的修正系数问题,在假设气井井筒中的液滴为扁平形,考虑曳力系数与雷诺数(1。
补充资料:边际产量(MP)
边际产量(MP):增加一个单位可变要素投入量所增加的产量。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条