说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 偏心动力拱
1)  eccentric dynamic bridge
偏心动力拱
2)  eccentric force
偏心力
1.
Research on eccentric force of sucker rod upsetting process;
抽油杆平锻工艺的偏心力研究
3)  Eccentric arm of force
偏心力臂
4)  eccentric moment
偏心力矩
1.
The production and change trend of copper water eccentric moment in converter process is discussed.
讨论了在转炉生产过程中炉内铜水偏心力矩的产生及其变化趋势 ,并提出了炉体在不同转角时炉内铜水偏心力矩的计算方
5)  Thrust misalignment
推力偏心
1.
Study on reliability for flight control system under influence of thrust misalignment;
推力偏心影响下的飞控系统可靠性研究
2.
The part s design tolerance, the processing tolerance and the assembling tolerance can cause thrust misalignment of solid rocket.
零部件的设计公差、加工误差和装配误差会使固体火箭发动机产生推力偏心。
3.
The pentahedral bicharacteristic curve grid can be applied to investigate the thrust misalignment characteristics in a unsteady f.
证明五面体双特征曲线网格方法可用来研究非定常流动条件下的推力偏心特性。
6)  thrust eccentricity
推力偏心
1.
Mass eccentricity,thrust eccentricity and windage are main factors affecting impact action and initial disturbance parameter values of rocket projectile in the direction pipe.
质量偏心、推力偏心和弹管间隙是影响火箭弹在管内碰撞作用和初始扰动参数值的主要因素,在考虑上述因素存在情况下,对火箭弹的碰撞运动进行仿真计算,得出一些有益结论。
2.
Based on ground launch test of an infrared air-to-air missile,the affection of target-radiation on missile anti-jamming is analyzed by digital simulation,then the influence of trace on orbit,postposition offing-axis angle and thrust eccentricity on missile beginning trace are also analyzed.
以某红外空空导弹地面靶试试验为背景,通过数字仿真分析了目标辐射特性对导弹抗干扰性能的影响,以及导弹轨上运动、后置离轴角、推力偏心等因素对初始弹道的影响。
3.
It showed that the influences from gyro zero-position,rocket thrust eccentricity,launch mode and downwash flow field caused by helicopter are evident.
分析结果认为导弹陀螺零位、发动机推力偏心、导弹发射方式、直升机旋翼下洗流场等因素的影响是显著的,特别是在这些因素的综合影响下,初始弹道将出现很大的偏离。
补充资料:在AutoCAD中偏心圆锥与偏心圆台实体的画法
现在要画一个偏心圆锥,底面在WCS的XY平面上,圆心(0,0,0),半径100,顶点(300,0,400)在ZX平面上.

1)连接PA,PB. A(-100,0,0) B(100,0,0)



图1



在当前坐标下:


2)延长PA到C,使PA=CA;延长PB到D,使PB=DB;


3)连接CD;


4)以CD为直径画圆;


5)用XLINE命令中的二等分选项作角CPD的角平分线PO,交CD于O;


6)过O作CD的垂线,交圆于E,F;



图2



7)用三点UCS命令,取三点为:O,P,C;


8)过点O作PO的垂线GO,交PC于G;



图3



9)再次用三点UCS命令,取三点为O,F,G;


10)现在就可以画椭圆锥了!
cone-e-c-捕捉O点-捕捉F点-捕捉G点-a-捕捉P点;



图4



11)回到WCS,剖切椭圆锥
SL-选择椭圆锥-回车-XY-回车-捕捉P点.


12)删除辅助线条.



图5

说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条