1) slab cooling
基质条冷却
1.
There were 12 treatments, included air humidity enrichment to 60% , air humidity control environment; slab cooling to 17 ℃ , control; slab moisture controlled by timer, set at 50% ,.
共设置了12种试验处理,包括提高空气相对湿度到60％、对照;基质条冷却至17℃、对照;基质条湿度设定为50％、60％、由定时器控制。
2) cooling condition
冷却条件
1.
The effects of the waveform of pulse electric current and cooling conditions on the anodic oxidation process and the microstructure and properties of the hard anodic oxidation coating of motor piston were investigated using a specially designed apparatus.
采用自制宽频脉冲电源和氧化装置对发动机铝活塞在不同脉冲电压波形和冷却条件下的硬质阳极氧化进行了研究。
2.
This program was applied to calculate the temperature distribution of copper thin-slab continuous casting with different casting speeds and cooling conditions.
利用该程序计算了不同拉速及冷却条件下, 铜薄板连铸过程中温度场的分布, 并分析了拉速、冷却条件对铸坯温度的影响。
3.
A multiphase model has been developed and applied to two dimension solidification processing of Al7 wet pct Si/SiC particles Fgm on different cooling conditions.
本文采用多相流模型对不同冷却条件下Al-Si/SiC系统二维凝固过程进行了数值模拟,对顶面冷却、底面冷却、侧面冷却和四面冷却条件下,无颗粒、小颗粒和大颗粒的情况进行了研究。
3) cooling conditions
冷却条件
1.
Through the experiments in which the grind-hardening of 65Mn steel has been carried out on a conventional surface grinder with alumina grinding wheel, the effect of the cooling conditions on the microstructures and properties in grind-hardened layer were investigated.
通过在普通平面磨床上采用刚玉砂轮对 6 5Mn钢进行磨削硬化试验 ,研究了冷却条件对其硬化层组织与性能的影响。
2.
For the optimization of the mould cooling conditions,FEM code Marc has been adopted for the numerical simulation of the influence of the mould water flow rate,the outlet/inlet water temperature difference,the temperature of the inlet cooling water,and the wide of the water gap respectively.
为优化结晶器冷却条件的需要,本文通过使用大型有限元分析软件 MARC 分别对结晶器冷却水量、进出水温差、进水温度和水缝宽度等因素变化的作用进行了计算模拟,得到并分析了其分别对大方坯在结晶器中凝固状态的不同影响程度。
4) Cooling medium
冷却介质
1.
Effects of different cooling medium on microstructure and mechanical properties of bainite wear resistant steel plate were investigated.
研究了不同冷却介质对贝氏体耐磨钢板组织和力学性能的影响。
2.
The effects of different cooling medium on microstructure and mechanical properties of new type bainite cast steel were studied.
研究了不同冷却介质对新型贝氏体铸钢组织和力学性能的影响。
3.
The experiment that effect of cooling mediums on γ′ precipitates and properties in FGH96 alloy was carried out by using optical microscope(OM) and field emission scanning electron microscope(FESEM).
采用光学显微镜(OM)和场发射扫描电镜(FESEM)对FGH96合金在不同冷却介质下γ′相的析出行为进行了实验研究。
5) quenchant
冷却介质
1.
The controllable quenching theory for water-base quenchants was studied.
研究了水基冷却介质量化淬火的新技术,提出了利用量化淬火调整介质冷却特性、提高淬火质量的新思路,给出了三个有效的量化淬火控制参数:质量比K,初始温度Ts,介质参数Q。
2.
The applications and developments of polymer quenchants are of great concern to the cooling technique.
聚合物冷却介质的应用和发展与冷却技术紧密相关。
6) coolant
[英]['ku:lənt] [美]['kulənt]
冷却介质
1.
A numerical investigation of the minimum coolant injection rate for transpiration cooling;
发散冷却最小冷却介质注射量的数值研究
2.
2 generator in Dazhai power station using the new coolant VXF-4310.
从流动和传热的角度看,VXF-4310作为电机蒸发冷却介质是可行的,从而为三峡机组采用该新型冷却介质提供了可靠的工程依据。
补充资料：箔条干扰火箭(见箔条投放装置)
箔条干扰火箭(见箔条投放装置)
chaff jamming rocket
botiao gQnrao huolian箔条干扰火箭(eha拜Jamming:ocket)见箔条投放装置。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条