1) Stock cutting
高杆插条
2) high-order spline interpolation
高次样条插值
1.
Study of empirical mode decomposition based on high-order spline interpolation;
基于高次样条插值的经验模态分解方法研究
3) cutting
[英]['kʌtɪŋ] [美]['kʌtɪŋ]
插条
1.
Anatomical study on rooting of Eurya japonica cutting;
柃木插条生根的解剖学研究
2.
Effect of SNP on rooting of hypocotyl cutting from mung bean seedling;
硝普钠SNP对绿豆下胚轴插条生根的影响
3.
Effects of ibuprofen on the cutting rooting, seedling quality of Dendranthema morifolium;
布洛芬对菊花插条生根、菊苗质量的影响
4) cuttings
[英]['kʌtiŋ] [美]['kʌtɪŋ]
插条
1.
An Anatomical Study on Rooting of Cuttings of Taxus cuspidata var. nana;
矮紫杉插条生根的解剖研究
2.
Effect of GL Rooting reagent on Rooting and Translocation of Carbohydrate in Cuttings of Hibiscus rosa sinensis L;
GL生根剂对扶桑插条生根及碳水化合物分配的影响
3.
After treatment of S 3307 used together with rooting powder (ABT), the water uptake of cuttings of Dendrocalamus brandisii increased and the chlorophyll catabolism decreased; the photosynthetic rate was promoted.
S3 3 0 7与ABT混合后处理的云南甜竹插条的水分上运加速 ,叶绿素降解延缓 ,光合速率提高 ,14 C 光合产物向插条基部的转运增加 ,插条的生根率高于S3 3 0 7或ABT单独处理
5) rod
[英][rɔd] [美][rɑd]
杆条
1.
The typical fluid-solid interaction analysis is used,the instance of big length-to-diameter ratio rods flight in the air is studied by 3-D numerical simulation,the attenuation coefficient of velocity and the distribution of equivalent stress is calculated for the rods with different dimensions.
利用典型的流—固耦合算法,对大长径比(L/D≥30)杆条在空气中飞行的情况进行三维数值模拟研究,计算了不同尺寸杆条的速度衰减系数和等效应力分布,并将数值模拟结果与试验结果进行了比较,为离散杆式战斗部设计和研究提供参考。
2.
In this paper,the model about the focusing width of the discontinuous rod warhead whose detonated way is central is presented.
介绍了中心起爆离散杆战斗部聚焦带宽的计算模型,给出了杆条微元初速和飞行方向的计算方法,在一定假设条件下,根据动量平衡,得到了杆条飞行初速和飞行方向的等效点,给出了杆条聚焦带宽的算例。
6) flagpole coor
插旗杆座
1.
This paper emphatically introduces injection mould design of flagpole coor and CAD/CAM process of its mould parts.
本文着重介绍插旗杆座的注塑模设计及模具零件的CAD/CAM过程。
补充资料：多功能高真空四螺杆反应混炼机
多功能高真空四螺杆反应混炼机
多功能高真空四螺杠夏应混蛛机 魂梆有机吐研究中。*稿
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条