1) ambient temperature creep
常温蠕变
1.
The ambient temperature creep behaviour of a heat ereated 40CrNiMoA steel under stresses lower than its yield strength was studied together with its influencing factors.
本文研究了热处理强化后的40CrNiMoA钢在低于屈服强度的应力作用下常温蠕变行为和影响因素。
2) Creep factor
蠕变常数
4) Room temperature creep
室温蠕变
1.
Room Temperature Creep and Its Effect on Fatigue Crack Growth of Structural Steels;
结构钢的室温蠕变及其对疲劳裂纹扩展的影响
2.
Room temperature creep at crack tip of a 0Cr18Ni9 stainless steel and its effect on the following fatigue crack growth have been investigated.
研究0Cr18Ni9不锈钢裂纹尖端的室温蠕变(room temperature creep,RTC)现象以及其对恒ΔK条件下疲劳裂纹扩展行为的影响作用。
3.
The phenomenon of room temperature creep(RTC) deformation and its effect on subsequent flow stress under various loading stress rate(Lsr) and loading process in a X70 pipeline steel were studied.
利用MTS万能试验机研究了X70管线钢在不同应力加载速率和不同加载过程下的室温蠕变现象,以及室温蠕变对流变应力的影响。
5) creep
[英][kri:p] [美][krip]
高温蠕变
1.
MSP testing has been used to evaluate high-temperature mechanical properties of MoSi_2 based composites including high-temperature strength,brittle-to-ductile transition temperature and creep resistance.
对MoSi_2系复合材料高温蠕变测试表明,MSP试验法得到的蠕变曲线和传统方法类似,而且随着氧化物添加相含量的增加,复合材料的高温蠕变性能下降。
2.
Inorder to improve the poor high temperature creep resistant property of AZ91, the development of high temperature creep resistant die-casting magnesium alloys were carried out.
针对商用压铸镁合金抗高温蠕变性能较差的现状,开发了抗高温蠕变压铸镁合金,其开发的目的是针对大马力柴油发动机汽缸罩盖,其抗高温蠕变性能应该能够保障其在150℃条件下稳定工作,而且其成本的增加应该控制在AZ91D合金成本的15%以内。
3.
According to bad high temperature creep resistant property and on the base of AZ91,the development of high temperature creep resistant die-casting magnesium alloys were carried out in this paper.
针对商用压铸镁各金抗高温蠕变性能较差的现状,开发了抗高温蠕变压铸镁合金,其开发的目的是针对大马力柴油发动机汽缸罩盖,其抗高温蠕变性能应该能够保障其在150℃条件下稳定工作,而且其成本的增加应该控制在 AZ91D 合金成本的15%以内。
6) high temperature creep
高温蠕变
1.
Effect of zinc content on high temperature creep property of AZ31 magnesium alloy;
AZ31镁合金中Zn含量对其高温蠕变性能的影响
2.
Researches on the High Temperature Creep Deformation of the Weld Seam Interfaces of Pressure Vessels of Clad Steel Plates
复合钢板压力容器焊缝界面高温蠕变研究
3.
The research progress of the high temperature creep and creepmechanism of carbon/carbon composites and carbon fibres at home and abroad are reviewed in this paper.
综述了国内外对碳/碳复合材料及碳纤维的高温蠕变及蠕变机理的研究情况。
补充资料：常温干燥
分子式：
CAS号：
性质：在常温条件下使涂膜干燥的工艺过程，也称自然干燥或空气干燥(air drying)。干燥时的气温、相对湿度和通风状况是影响干燥的重要因素。温度一般为10～35℃，相对湿度为75％以下，室内通风量为6～10次/h；室外风速在3级(3.4～5.5m/s)以下为宜。
CAS号：
性质：在常温条件下使涂膜干燥的工艺过程，也称自然干燥或空气干燥(air drying)。干燥时的气温、相对湿度和通风状况是影响干燥的重要因素。温度一般为10～35℃，相对湿度为75％以下，室内通风量为6～10次/h；室外风速在3级(3.4～5.5m/s)以下为宜。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条