1) shock-wave strength
激波强度
1.
In accordance with the program be selfweaved,we calculate successfully Franck-Condon factors of main molecular band systems in high temperature air,such as O2 (S-R ), N2 (1+ )N2 (2+ ),N(2+) (1-),NO (β) and NO (r),Thus, the folowing relation are obtained; such as the relation between shock-wave strength and the temperature of incident or reflected shock-wave at the pressure, 10 torrs in the.
从而得出：当激液管低压端的空气压强为1333Pa时，入射激波及反射激波后高温空气的温度与微波强度的关系；各主要分子带系转动态分布与温度的关系；高温空气中主要分子带系F－C因子与激波强度的关系。
2) inviscid shock strength
无粘激波强度
3) shock intensity effect
激波强度效应
4) strong shock wave
强激波
1.
A modified ghost fluid method for strong shock wave impacting on material interface;
用改进的ghost fluid方法模拟强激波与界面的相互作用
2.
The vibrational temperature and electron number density behind strong shock waves were measured in shock tubes,and the results were compared with those of theoretical calculation.
利用测量强激波波后N2+第一负系(0,0)带和(1,2)带的辐射,对强激波后振动温度历程的测量过程进行了探索,并利用Langmuir探针技术,在低密度激波管中对强激波后电子数密度历程进行了测量。
5) strong normal shock waves
强正激波
1.
A numerical simulation is described for nonequilibrium flows of high temperature gas behind strong normal shock waves with chemical reactions by using a three temperature kinetic model.
利用三温度动态模型，对具有化学反应的强正激波后的高温气体的非平衡流动进行了数值模拟，在较宽的马赫数范围内（６～２６），计算出了各种气动参数及气体组分在非平衡区随时间的变化历程，并与有关文献进行了比较。
6) laser intensity
激光强度
1.
The relation between the laser cavity s pressure of the Visx20/20B Excimer laser system and the laser intensity;
VISX20/20B准分子激光治疗仪激光腔压力与激光强度的关系
2.
The effect of the irradiation time,laser intensity and spot diameter on the mass ablative rate of carbon fiber reinforced silicone modified epoxy resin composite was analyzed respectively.
研究结果表明:激光辐照时间对该复合材料的质量烧蚀率的影响不大,而该复合材料的质量烧蚀率随入射激光强度和光斑直径的增大而增大。
3.
To analyze and to deduce the effect of laser intensity on ignition of energetic materials,according to the thermal mechanism of laser ignition,the relation between laser diode ignition time t i and laser power density I 0 is obtained by applying thermal transmission theory,simplified model as well as approximate method.
从激光点火的热作用机理出发，运用传热理论，采用简化模型和近似方法，分析推导激光强度对含能材料点火的影响，得出激光二极管点火时间 ｔｉ 与激光功率密度 Ｉ０ 的关系，进而得到激光二级管点火能量 Ｅｉ 与 Ｉ０ 的关系，并和实验结果作了比较。
补充资料：表光合强度(见光合强度)
表光合强度(见光合强度)
forecast of sowing or transplanting time
b iaoguanghe qiangdu表光合强度见光合强度
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条