1) parametric shimmy
参数摆振
1.
On the basis of reference[6], the influence of damping of shimmy damper, momentof inertia of wheel, tire cornering stiffness and strut tilt stiffness on parametric shimmy stability of aircraft wheel is investigated in the paper.
本文在文献[6]的基础上,首次研究了减摆器阻尼,机轮转动惯量、轮胎偏滚刚度、支柱侧倾刚度对飞机机轮参数摆振稳定性的影响。
3) oscillation parameter
振动参数
1.
This paper compared continuous casting mold oscillation types between nonsinusoidal oscillation and triangle oscillation, analyzes their oscillation waves and oscillation parameters.
本文对非正弦振动和三角形振动这两种不同的连铸结晶器振动方式进行比较，分析二者振动波形及振动参数，确定适合高速连铸的振动参数的选择范围，选出最佳的振动形式。
2.
This paper establishes the velocity equations of new trapezoid oscillation, analyzes its oscillation parameters, and proposes its optimum regions.
本文建立了新梯形振动的速度表达式，并对其振动参数进行了分析，确定其最佳选择范围。
4) vibration parameter
振动参数
1.
Design of PVDF sensor measuring vibration parameters;
测量多振动参数的PVDF传感器的设计
2.
An L27(313)orthogonal array based on Taguchi method was adopted,the results showed the effects of the dynamic injection molding parameters on shrinkage of parts were different between perpendicular flow direction and parallel flow direction,and the effects of vibration parameters on the sh.
文中采用L27(313)正交矩阵进行实验,试验结果表明:动态注塑参数对制品的垂直于流动方向与平行于流动方向收缩的影响是不同的,振动参数对两个方向上收缩率的影响都较强,说明振动力场的引入能使聚合物加工过程发生变化。
3.
Through drawing and analyzing the cutting trace of the slice lapping,the selection of appropriate vibration parameters is mainly discussed in order to achieve the best slice lapping e.
通过分析和绘制研磨的切削轨迹,着重讨论如何确定合适的振动参数,以达到最佳的研磨效果。
5) parametric resonance
参数共振
1.
Optimal control of parametric resonances of a clamped-clamped pipe conveying pulsating fluid;
两端固定输流管道在脉动内流作用下参数共振的最优控制
2.
Stability and parametric resonances of a pipe conveying pulsating fluid;
输流管道的参数共振及系统参数对共振区域的影响
3.
Swing- mechanical model, elementary analysis and perturbation solution for nonlinear parametric resonance;
秋千——力学模型,初等分析与参数共振微扰解析解
6) Vibration parameters
振动参数
1.
Research on effects of vibration parameters on stainless steel cutting by diamond tool;
振动参数对金刚石切削不锈钢零件影响规律研究
2.
Helical vibration dryer and design of its vibration parameters;
螺旋振动干燥机及其振动参数设计
3.
The vibration parameters of the fiberboard, including specific dynamic Young's modules E/ρ,acoustic radiation damping (E/ρ3)~(1/2) , acoustic impedance (Eρ)~(1/2) ,(E/ρ)~(1/2) and Eccc, are measured by flexural vibration.
利用弯曲振动法测取了纤维板的比动态弹性模量E/P、声辐射阻尼系数(E/P3)~(1/2)、声阻(Eρ)~(1/2)及(E/ρ)~(1/2)、Eρ等振动参数,并利用回归方法分析了这些参数与静曲强度的相关性。
补充资料：振摆
1.抖动。 2.犹跌宕。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条