1) modified SBR
改性丁苯橡胶
1.
The aramid bulletproof laminates have been made with the modified SBR, as the matrix and with the aramid woven fabric and laid cloth as the reinforcer.
以改性丁苯橡胶为基体,以Kevlar(芳纶)织物及无纬布为增强材料,制备了芳纶防弹板。
2) modified poly-chloroprene rubber
改性氯丁橡胶
1.
By using modified poly-chloroprene rubber as basic material and poly-isocyanate as curing agent, a new fire retardant adhesive for conveyor belt has high bonding strength,fine heat-resistance,quick drying and flame retardant etc Applying this adhesive into bonding conveyor belt joint at room temperature and normal pressure , the belt can be put into use 30 min later after bonded
以改性氯丁橡胶为主料、多异氰酸酯为固化剂制成的新型难燃输送带胶粘剂,具有粘接强度高、耐热性好、干燥时间短、难燃等特点,在常温常压下粘接输送带接头,固化30min即可负荷运行。
3) the modification of nitrile rubber
丁腈橡胶改性
1.
In order to improve the service life of the screw pump,the rubber types in a screw pump stator and the advanced research on the modification of nitrile rubber in recent years are summarized.
针对提高采油螺杆泵工作寿命的问题,介绍了国内外螺杆泵定子橡胶材料的类型和近年来丁腈橡胶改性研究的新进展,有利于定子橡胶性能的进一步改进。
4) modified IIR
改性丁基橡胶
5) SBS
热塑性丁苯橡胶
1.
FLAKING METHOD OF MEASURING THE PHYSICAL PERFORMANCE OF SBS SAMPLE;
测定热塑性丁苯橡胶颗粒样品物理性能的制片方法
2.
The thermoplastic elastomer from SBS/LDPE blend having excellent mechanical properties,such as high mechanical strength and elongation at break and repeatable processability,was prepared by partial dynamic vulcanization.
选用热塑性丁苯橡胶(SBS)和低密度聚乙烯(LDPE)为主体材料,采用部分动态硫化法制备了一类性能良好的材料热塑性丁苯橡胶 低密度聚乙烯共混型热塑性弹性体,具有力学强度高,断裂伸长率大,可重复加工等特点,并研究了聚烯烃的品种、橡塑比、硫化体系等因素对动态硫化SBS LDPE热塑性弹性体力学性能的影响。
6) styrene butadiene rubber
丁苯橡胶
1.
Preparation of epoxidized styrene butadiene rubber by formic acid-hydrogen peroxide;
用甲酸-过氧化氢法制备环氧化丁苯橡胶
2.
Effect of increasing conversion on performance of emulsion polymerized styrene butadiene rubber;
提高转化率对乳聚丁苯橡胶性能的影响
3.
Treatment of waste water from styrene butadiene rubber production with mixed system of ferrous sulfate and hydrogen peroxide;
用硫酸亚铁和过氧化氢混合体系处理丁苯橡胶生产废水
补充资料：丁腈橡胶改性酚醛压塑粉
分子式：
CAS号：
性质：将丁腈橡胶塑炼，再与酚醛树脂、木粉或矿物填料、固化剂、润滑剂混合，经辊压、粉碎而成丁腈橡胶改性酚醛模塑粉，用于制造嵌有金属配件的复杂制件，以及适宜于湿热条件下工作的机电产品的绝缘结构件。
CAS号：
性质：将丁腈橡胶塑炼，再与酚醛树脂、木粉或矿物填料、固化剂、润滑剂混合，经辊压、粉碎而成丁腈橡胶改性酚醛模塑粉，用于制造嵌有金属配件的复杂制件，以及适宜于湿热条件下工作的机电产品的绝缘结构件。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条