说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 侧压效应系数
1)  lateral pressure effect coefficient
侧压效应系数
1.
The lateral pressure effect coefficient and the confinable effect coefficient of the concrete filled steel tube are analyzed theoretically.
对钢管砼侧压效应系数及约束效应系数进行了理论分析 ,建立了二者的关系 并提出了能有效限制核心砼横向变形的约束效应系数的范
2)  Side pressure coefficient
侧压系数
1.
The influences of friction coefficient and side pressure coefficient on crack tip stress intensity factor were analyzed.
采用"裂纹线应力场"分析方法,推导双轴压缩下有限岩板内闭合裂纹尖端应力强度因子的近似解析解,分析裂纹表面摩擦因数、侧压系数对裂尖应力强度因子的影响;运用有限元法对同一问题进行数值研究,并与解析解进行比较。
3)  lateral pressure coefficient
侧压系数
1.
Simulation results indicated that the cracks initiation and propagation related with not only the lateral pressure coefficient(λ) but also the tunnel s geometrical figure.
模拟现象与理论分析相符;隧道裂纹演化规律不仅与侧压系数有关,而且还与隧道的几何形状相关;验证了裂纹演化过程中初始裂纹和远区裂纹的存在。
2.
Under different lateral pressure coefficients,the dynamic response characteristics of the pillar are characterized;and the effect of the duration of dynamic disturbance on the pillar stability is studied.
通过改变侧压系数,来改变岩柱所受的地应力状态,进而分析不同应力状态下岩柱对外界动力扰动的力学响应;通过改变动态扰动的作用时间,来分析动态扰动时间的变化对处于不同应力状态下的岩柱稳定性的影响。
4)  coefficient of horizontal pressure
侧压系数
1.
The calculation method of vertical pressure component of in-situ ground stress and the coefficient of horizontal pressure were proposed.
2 m以下处于静水压力状态,侧压系数变为1。
5)  side thrust effect
侧压力效应
6)  lateral pressure coefficient
侧压力系数
1.
Research on staged characteristics of lateral pressure coefficient K_0 of soft clay;
软黏土侧压力系数K_0阶段性特征研究
2.
A study on the lateral pressure coefficient Ko value test of the Changchun clay soil;
长春粘性土的侧压力系数K_0值试验研究
3.
A nonlinear elastic analysis of static stress and lateral pressure coefficient for granular Couette systems;
Couette颗粒系统中静态应力和侧压力系数的非线性弹性理论分析
补充资料:压下系数


压下系数
coefficient of reduction

yaxia xishu压下系数(eoeffieient of reduetion)轧件变形前的高度H和变形后的高度h之比,一般以,表_H,_.~,,,__一~,___一‘.示,”一甘。根据体积不变条件,压下系数。与延伸系数产、宽展系数。之间有以下关系:粤。。一:,或l。粤 ’-一’一一’一’--一7‘一一’专+ln。+hi产~o。上面两式说明,由一个主变形方向压下来的金属,按不同比例分配到另外两个主变形方向,例如轧制时一定的压下量将会得到一定的宽展量和延伸量。 (余望)
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条