1) Range coding device+
距离编码器+
2) distance
距离
1.
Effect of Distance between Clamp and Cutting Notch on Plywood Bond Strength Testing;
夹具与槽口距离对胶合板强度测定结果的影响
2.
Measurement of the distance between uretero and uterine neck in the condition of enlargement of uterine neck;
子宫颈增大状态下输尿管与子宫颈间距离的测量
3.
Study on the Correlation of Distance and Angle with the Image of Laryngostroboscope;
测量距离和角度与喉动态镜图像关系的实验研究
3) Range
距离
1.
Joint frequency、direction of arrival and range estimation for near-field sources;
近场源频率、波达方向和距离的联合估计方法
2.
The speed of moving-target was measured based on the principle of PD frequency shift,and the range of moving-target on the pulse-echo principle.
利用多普勒频移原理实现了运动目标速度测量,利用脉冲回波测距原理实现运动目标距离测量。
3.
For the accuracy of range information is higher than that of azimuth information received by networking radar system,three-dimension target location based on range only is proposed by using the linear least square iteration algorithm.
在雷达组网背景下,针对雷达测量距离精度较高,测量方位精度较低的特点,利用组网雷达的距离信息,采用线性最小二乘迭代算法对目标三维定位进行了分析,并就迭代初始值给出了一种解决方法,不仅可以避免迭代结果的发散,而且可以提高线性最小二乘迭代算法的收敛速度。
4) metric
距离
1.
The metric and closure operator are defined,a unique topology space on is obtained.
在集合〔F〕上定义距离p及闭包运算C*,则在〔F〕上存在唯一的一个拓扑T使得在拓扑空间(〔F〕,T)中,对任意的集合Γ〔F〕都有C*(Γ)=Γ。
2.
This thesis, according to the 10-year-long lectures on the theory of metric space in different courses, summaries a few points , which should be paid attention to, on how to well explain the concepts of metric and metric space.
通过十多年来在不同课程中讲解距离空间的理论,总结出要讲解好“距离”、“距离空间”的概念应注意的几个方面的问题。
5) "distance"
“距离”
6) Euclidean distance
欧式距离
参考词条
补充资料:编码器
编码器
encoder
b旧nmoq,编码器(e ncoder)能将每一根输人线上的信号转换成输出端上的一个对应代码,即实现输人信号编码功能的组合逻挥电路。它广泛用于逻辑电路中。 图示是一个8线一3线编码器的逻辑图,其中I。~I:是八个输人端,YZ、Yl、Y。是三个输出端。当在输人端加上逻辑l信号时,便在YZ、Y、、Y。给出一个对应的三位二进制代码。输人信号与输出代码的省昔阵矛10一卜一h8线一3线编码器的逻辑图对应关系如表1所示。衰1圈中电路的功能裹┌───────────┬────┐│101一12 13 10 101‘17 │YZ Yz Yo│├───────────┼────┤│1 0 0 0 0 0 00 │0 00 │├───────────┼────┤│0 1 0 0 0 0 00 │0 01 │├───────────┼────┤│0 0 1 0 0 0 00 │0 10 │├───────────┼────┤│0 0 0 1 0 0 00 │0 11 │├───────────┼────┤│0 0 0 0 1 0 00 │1 00 │├───────────┼────┤│0 0 0 0 0 1 00 │1 01 │├───────────┼────┤│0 0 0 0 0 0 10 │1 10 │├───────────┼────┤│0 0 0 0 0 0 01 │1 11 │└───────────┴────┘ 在图示编码电路中,任何时候只允许有一个输人信号是l,否则电路不能正常工作。为克服这种局限性,便产生了优先编码器(priority eneoder)。设计优先编码器电路时,预先把所有的输人信号按优先权的高、低排队,当两个以上输人信号同时为1时,只对其中优先权最高的一个进行编码。表2是8线一3线优先编码器功能表,表中的“x”表示既可以是逻辑。,也可以是逻辑l。从表2中不难看出,输人信号I,的优先权最高,I。的优先权最低。例如当17~l时,无论I。~1。当中还有多少个是1,电路只对卜进行编码,使输人为Y:Y IYo=111。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。