1) the best setup temperature
最佳安装温度
1.
Based on the analysis results,some suggestions for the design parameters and the best setup temperature are proposed.
并根据分析计算的结果 ,对波纹管伸缩节中波纹管的各项参数提出了参考意见和最佳安装温度的计算公
2) optimal temperature
最佳温度
1.
A mathematical model of expressing the relatinnship between the optimal temperature (Tm) and the height of the catalyst bed(L ), the optimal CO conversion ratio (xCO,m)or the optimal CO composition (yco,m) and the height of the catalyst bed (L ) has been established.
建立了一氧化碳变换反应催化剂床层中最佳温度（Ｔｍ）与床层高度（Ｌ）、最佳一氧化碳转化率（ｘｃｏ，ｍ）或最佳一氧化碳浓度（ｙｃｏ，ｍ）与床层高度（Ｌ）关系的数学模型，绘制了Ｔｍ－Ｌ、ｘｃｏ，ｍ－Ｌ和ｙｃｏ。
3) optimum temperature
最佳温度
1.
The effect of Fe_2O_3 on medium temperature FGD characterization,optimum temperature in fixed bed and proportion of Fe_2O_3 and CaO were studied in the experiment.
研究了加入氧化铁添加剂后,对中温烟气脱硫性能的影响和对固定床干法脱硫最佳温度的影响,氧化铁配比对氧化钙脱硫性能的影响等。
2.
The optimum acidity and optimum temperature of cellulose degradation by cellulase were obtained.
用微量热法测定了不同酸度和不同温度下纤维素酶降解纤维素的热功率—时间曲线,应用热动力学理论和对比进度法解析出反应的米氏常数(Km)和最大速率(Vmax),并得出速率常数k2,建立速率常数与酸度和温度间的关系式,从而获得纤维素酶降解纤维素的最佳酸度和最佳温度。
3.
The optimal mathematical models on the axial optimum temperature and maximum synthetic rate for a continuous heat exchange ammonia converter were established.
建立了连续换热式氨合成塔轴向最佳温度和最大合成率的优化模型,采用牛顿迭代法和龙格-库塔法对模型进行了数值解。
4) optimalleaf installation angle
最佳叶片的安装角度
5) The Best Heat Preservation Temperature
最佳保温温度
6) optimal location
最佳安装位置
1.
The particle swarm optimization(PSO) technique is applied to find the optimal location of TCSC with maximum system load ability and minimum cost of installation of TCSC.
提出一种采用粒子群优化技术,以系统载荷能力最大化及安装费用最小化为目标,确定TCSC最佳安装位置的方法。
2.
A simple particle swarm optimization (PSO) algorithm is adopted for finding out the most sensitive lines, and in which lines, the optimal locations of TCSC is determined by modified particle swarm optimization (MPSO) algorithm, and the optimal number and the optimal parameter settings of TCSCS are gotten to maximize the transfer capability in power system.
提出了一种新的TCSC选址方法,采用简易粒子群算法求出系统中较为敏感的支路群,用改进的粒子群算法在较敏感支路群中确定TCSC的最佳安装位置,并求出TCSC的最佳安装个数和安装容量,来达到系统输电能力最大的目的。
补充资料：设备的安装——设置安装基准
设备的安装——设置安装基准   | ||
|
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条