1) optimal annealing temperature
最佳退火温度
2) optimal temperature
最佳温度
1.
A mathematical model of expressing the relatinnship between the optimal temperature (Tm) and the height of the catalyst bed(L ), the optimal CO conversion ratio (xCO,m)or the optimal CO composition (yco,m) and the height of the catalyst bed (L ) has been established.
建立了一氧化碳变换反应催化剂床层中最佳温度（Ｔｍ）与床层高度（Ｌ）、最佳一氧化碳转化率（ｘｃｏ，ｍ）或最佳一氧化碳浓度（ｙｃｏ，ｍ）与床层高度（Ｌ）关系的数学模型，绘制了Ｔｍ－Ｌ、ｘｃｏ，ｍ－Ｌ和ｙｃｏ。
3) optimum temperature
最佳温度
1.
The effect of Fe_2O_3 on medium temperature FGD characterization,optimum temperature in fixed bed and proportion of Fe_2O_3 and CaO were studied in the experiment.
研究了加入氧化铁添加剂后,对中温烟气脱硫性能的影响和对固定床干法脱硫最佳温度的影响,氧化铁配比对氧化钙脱硫性能的影响等。
2.
The optimum acidity and optimum temperature of cellulose degradation by cellulase were obtained.
用微量热法测定了不同酸度和不同温度下纤维素酶降解纤维素的热功率—时间曲线,应用热动力学理论和对比进度法解析出反应的米氏常数(Km)和最大速率(Vmax),并得出速率常数k2,建立速率常数与酸度和温度间的关系式,从而获得纤维素酶降解纤维素的最佳酸度和最佳温度。
3.
The optimal mathematical models on the axial optimum temperature and maximum synthetic rate for a continuous heat exchange ammonia converter were established.
建立了连续换热式氨合成塔轴向最佳温度和最大合成率的优化模型,采用牛顿迭代法和龙格-库塔法对模型进行了数值解。
4) annealing temperature
退火温度
1.
Effect of annealing temperature on the microstructure of rapidly-solidified TiNi-Cu alloy ribbons;
退火温度对Ti_(53.5)Ni_(22.8)Cu_(23.7)合金快速凝固条带组织的影响
2.
Influence of annealing temperature on structure and properties of Al-6Mg-Sc-Zr alloy;
退火温度对Al-6Mg-Sc-Zr合金组织与性能的影响
3.
Effects of annealing temperature on microstructures and properties of the 25Mn-3Si-3Al-TWIP steel;
退火温度对25Mn-3Si-3Al-TWIP钢组织和力学性能的影响
5) anneal temperature
退火温度
1.
Effect of anneal temperature on performance of poly(chloro-p-xylylene)films;
退火温度对聚氯代对二甲苯膜性能的影响
2.
Taking original shape examination as contrast,the HT250 welding strain under three kinds of different anneal temperature(500℃、600℃、650℃)was studied.
以未进行退火处理试件为对比,研究了三种不同的退火温度(500℃、600℃、650℃)对HT250焊接残余应力的影响;对四块试件分别测试了各自的焊接应力,并将测试数据输入计算机得到了不同退火温度下的试件的焊接应力曲线;结果表明:此试验的最佳退火温度为650℃。
3.
The paper studies the effect of different cold deformation and anneal temperature as well as holding time on the material organization and property of alloy pipe 5086,sets the production process system of aluminum alloy 5086 at state of H34.
研究了不同冷变形程度、退火温度与保温时间对5086铝合金管材组织及性能的影响,确定5086铝合金H34状态的生产工艺制度,在工业生产条件下,其产品的技术指标达到了用户要求。
补充资料：软化退火(见低温退火)
软化退火(见低温退火)
soft-annealing
rU0nhUO tUihUO软化退火(soft一annealing)见低温退火。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条