1) beam loss control
束损控制
2) Constrained control
约束控制
1.
At the same time, an inferential control scheme with constrained control based on soft-sensor was designed.
同时并根据实际的质量控制目标,设计了一个基于软测量的推断控制方案,并在推断控制算法中增加了约束控制功能,增强了控制系统的可靠性和实用性。
2.
A constrained control system on two OXO reactors was implemented based a modular multivariable predictive control algorithm.
提出了一种模块多变量预测控制算法 ,实现了两个并列运行的羰基合成反应器的约束控制 ,使两个反应器出口的CO分压都保持在工艺约束范围内 ,同时将反应器进料配比控制在反应器在线操作优化软件给出的最佳值附近。
3.
A method was proposed in the paper that the output error curve in constraint zone is between(y sp -y)by setpoint control and zero by conventional treatment for constrained control,and can be designated with an exponent n(≥1)for different purposes.
针对约束控制中输出偏差处理方法 ,一改过去约束区间内输出偏差为 0、区间外为e =ysp -y的简单处理方法 ,提出的新方法可以避免在约束边界上跳变 (偏差函数连续 )、保证测量值尽量往中心给定值靠近。
3) constraint control
约束控制
1.
Research on constraint control method by feature-based multi-resolution modeling
基于多分辨率特征造型模型的约束控制方法研究
4) control constraints
控制约束
1.
Taking account of the event-driven actuators/controllers,clock-driven sensors,constant sampling period and uncertain time-delay less than one sampling period,the state feedback networked control system with control constraints is modelled as a discrete time-variant system with uncertainty.
考虑控制器和执行器事件驱动、传感器时钟驱动、恒定周期采样和不大于一个采样周期的不确定时延,将有控制约束的状态反馈网络控制系统建模为含有不确定性的离散时变系统。
5) beam control
波束控制
1.
Combined with a burst angle algorithm, this paper uses a beam control technology of the one-dimension phase array fuze to change the fuze beam adaptively and achieve the optimal initiating control.
利用一维相控阵引信的波束控制技术,自适应地改变波束倾角并结合起爆角算法实现最佳起爆控制。
2.
Starting from the view of engineering practice,a method of optimizing and improving a radar beam control algorithm is presented.
从工程实践角度出发,提出了一种对某雷达波束控制算法进行优化改进的方法。
3.
The implementation of amplitude weighting and beam control are elaborated with indexes and test results.
介绍了一种容差性好、馈线损耗小并能实现5波束准确定位的二维平面相控阵风廓线雷达馈线系统的组成及主要设计特点,详细介绍了馈线系统的工作原理、幅度加权和波束控制的实现方法,给出了实现的指标和实验测试结果。
6) Beamline control
束线控制
补充资料：扣损余额全损
扣损余额全损
【扣损余额全损]财产保险理赔业务常用术语。从保险标的全损额中扣除出售损余物资所得加上出售及检验费用后的全部净损失额。保险人负责赔付保险金额与出售损余物资所得款项扣除出售费用和检验费用之后的差额。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条