1) continuous straightening mechanism
连续拉直
1.
Design problem of small-sized continuous straightening mechanism of reinforcing bars;
小型钢筋矫直机连续拉直机构的设计问题
2) up-draw
垂直连续拉制
3) continuous stretching leveller
连续式拉伸矫直机
4) continuous stretch bending leveller straightener
连续式拉伸弯曲矫直机
5) continuous drawing
连续拉伸
1.
The continuous drawing method for strip material with notching was introduced with the design of progressive die for thin wall and wide flange truckfest component as example.
以薄壁宽凸缘筒形件级进模的设计为例,介绍了采用带料切口连续拉伸方法,包括步距冲裁、切口冲裁、连续拉伸、冲孔、翻边和落料,生产效率较高。
2.
Both the drawing characters of stainless steel and the forming technology character of its linker shell are analyzed, and the technology calculations are completed, the key points of continuous drawing layout and die design are stressed and stated.
分析了不锈钢拉伸特性及连接器外壳成形工艺特点,并进行了工艺计算,重点阐述了连续拉伸排样与模具设计要点。
6) continuous stay cable
连续拉索
1.
Based on the analytical models of rain-wind induced vibrations of continuous stay cables established by the authors, an analytical model which studies the effectiveness of dampers to rain-wind induced vibrations is presented.
在作者建立的三维连续拉索风雨激振理论模型的基础上,建立了阻尼器控制三维连续拉索风雨激振的新理论模型。
2.
Using three-dimensional continuous stay cables as objects, the partial differential equations for stay cables with rain-wind-induced vibration are derived and an analytical model for rain-wind-induced vibration of three-dimensional continuous stay cable is developed.
首先将水线固定在拉索表面,得到了典型驰振的响应;接着详细研究了来流风速、水线振动频率、水线形成位置、风速剖面和拉索阻尼比等对三维连续拉索的风雨激振响应的影响。
补充资料：直型连续聚合管
分子式：
CAS号：
性质：工业上生产聚己内酰胺大多采用连续法直形聚合管(有称VK管)。生产一般纺织用丝的高聚物用一段聚合或两段聚合(前聚合和后聚合)。而生产工业用高黏度高聚物用两段聚合，甚至用三段聚合。聚合管为不锈钢制成的封闭式直形管。由多节外有加热夹套管分段由法兰连接而成。聚合管直径可大至2m。由于熔体流动和温度有高度均匀要求，管内结构设计须特殊考虑。管子顶部有原料和助剂加入管和单体和水分排出分馏管。而底部则由输出泵进行铸带、切片。
CAS号：
性质：工业上生产聚己内酰胺大多采用连续法直形聚合管(有称VK管)。生产一般纺织用丝的高聚物用一段聚合或两段聚合(前聚合和后聚合)。而生产工业用高黏度高聚物用两段聚合，甚至用三段聚合。聚合管为不锈钢制成的封闭式直形管。由多节外有加热夹套管分段由法兰连接而成。聚合管直径可大至2m。由于熔体流动和温度有高度均匀要求，管内结构设计须特殊考虑。管子顶部有原料和助剂加入管和单体和水分排出分馏管。而底部则由输出泵进行铸带、切片。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条