1) topping heavy oil supply system
前置重油供油系统
2) fuel system automatic timing advance unit
燃油系统自动提前供油装置
3) Fuel supply system
供油系统
1.
In this paper some new technologies of improvementof DME fuel supply systems are introduced: Two-fluid thermodynamic pump、Variable-displacement rail-pressure supply pump and a novel fuel injection system, and the latest developmentof sealing an.
由于液态DME具有高压缩性和低润滑性,对供油系统的改造仍是目前开发DME发动机的关键。
2.
Then influences of cycle-to-cycle variation are analyzed when the fuel supply system parameters such as the fuel supply time-θfs,the pressure of injection- pjo ,th.
研究了采用低旋流进气,浅ω型燃烧系统的SD2100直喷柴油机的循环变动及其影响因素,分析了标定工况下的最高燃烧压力(P_(max))及其所在时刻(φ_A)、最大压力升高率(λ_p)及其出现时刻(φ_B)、平均指示压力(P_i)的循环变动;对供油系统中的供油提前角(θ_(fa))、启喷压力(P_(jo))及喷油嘴孔径(D)等参数进行调整,分析了对循环变动的影响,并综合燃油经济性指标,得到最优匹配。
3.
The problems existing in the fuel supply system on the KD 71 generator car are analyzed.
对 Ｋ Ｄ７１型发电车燃油供油系统存在的问题进行了分析，认为主要是该系统柴油粗滤器选型不当，并针对这一问题提出了具体改进方案。
4) fuel system
供油系统
1.
Discussion on enhancing reliability of fuel system of diesel engine
提高柴油机供油系统可靠性探讨
2.
In order to study the cavitation erosion mechanism of aero-engine fuel system,the failure analysis of three components in aero-engine fuel system,which were made of TC6 titanium alloy,ZL101 aluminum alloy and 2Cr3WMoV steel respectively,was processed.
为了研究航空发动机供油系统部件的气蚀失效机制与规律,分析了航空发动机供油系统中三种典型合金(TC6钛合金、ZL101铝合金、2Cr3WMoV钢)部件的气蚀原因,并比较了其气蚀特点。
3.
Studies a fuel system for use in a vehicle gas turbine.
对车用燃气轮机的供油系统进行了设计。
5) oil supply system
供油系统
1.
Design of a general oil supply system using integrative pumping station;
采用一体化集成泵站的通用供油系统设计
2.
Technical measures for improving the operation reliability of oil supply system of synthesis gas centrifugal compressor in 300,000 MTPA ammonia plant;
提高30万吨合成氨用离心式合成气压缩机供油系统运行可靠性的技术措施
3.
Thorough reconstruction of oil supply system for 200 MW steam turbine in Shajiao A Power Station;
沙角发电A厂200MW汽轮机供油系统完善化改造
6) fuel injection system
供油系统
1.
By means of a commercial software,FLOWMASTER,simulation of the operation of diesel engine fuel injection system has been carried out,and optimization of the injection process on several system parameters has been performed.
使用商业软件FLOWMASTER对柴油机供油系统及其工作过程进行模拟 ,并用之于某些参数的优化匹
2.
In this paper,it can be improved by improving fuel injection system and using EGR,the results show that the postponing injection timing,lowering injection pressure,suppressing initial injection rate,using EGR and the combination of the aboved methods can decrease exhaust emissions effectively.
:通过改进柴油机供油系统和利用废气再循环来改善混合气质量和燃烧过程 ,进而降低其有害排放。
3.
In this paper, the process of the selecting and the matching of fuel injection system (FIS) were introduced.
本文介绍了单缸增压柴油机供油系统选择与匹配过程，探讨了喷油泵主要结构、运转参 数对循环供油量、喷射压力、喷油延续角的影响；研究了加大循环供油量同时提高喷射压力的途 径，并通过实验，验证这些途径的可行程度。
补充资料：供置
1.供应措办。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条