1) crooked process radius
弯折半径
1.
According to analysis for 03G101-1《Structure of concrete construction drawing plane whole show method drawing rule and construct detail drawing》, to girder and post value of portrait the crooked radius, affect of steel-muscle hoop of the crooked process radius in girder and post argue to the new point of view through main steel-muscle design position.
根据 0 3G10 1— 1《混凝土结构施工图平面整体表示方法制图规范和构造详图》的分析 ,对梁、柱纵向弯折半径的取值 ,箍筋弯曲加工半径对梁柱中主筋设计的影响提出新的观点。
2) turning radius
转弯半径
1.
bending operation of the foundation was introduces,the plane bending belt conveyor to change the natural mechanics and reasonable method of determining the turning radiuswere described,and explore the impact of the belt conveyor plane bending operation of the relevant factors and the introduction of measures to plane bending belt conveyor design were eplored,the installation and use of provid.
在介绍实现弯曲运行措施的基础上,阐述了平面弯曲带式输送机自然变向的力学原理以及合理确定转弯半径的方法,并探讨了影响带式输送机平面弯曲运行的因素以及采用的相关措施,为平面弯曲带式输送机的设计、安装及使用提供必要的理论依据。
2.
Saturation time headways with different lane widths and turning radiuses were measured on the spot and abnormal data were identified and eliminated.
针对我国现有道路交通条件下典型的信号控制交叉口,对不同车道宽度、转弯半径的右转车道的饱和车头时距进行现场测定。
3.
This article analyses the differences between articulated bus and non-articulated bus when they make turn,and derives the calculation methods of the turning radius and passageway width of articulated bus and the angle between the main bus and the sub-bus.
分析铰接式客车和非铰接式客车转弯时的不同,并推导铰接式大客车转弯半径、通道宽度及主、副车之间夹角的计算方法。
3) bending radius
弯曲半径
1.
The design of the Decorative Stainless-Steel Elbow, the calculation of the thinnest thickness of the elbow wall, and the calculation of the smallest relative bending radius of the elbow, the forming die for the elbow and the attention items in the design of the die were introduced.
介绍了不锈钢装饰弯头的设计、弯头最小壁厚的计算、弯头最小相对弯曲半径的计算 ,并介绍了弯头成形模以及模具设计中应注意的问题。
2.
The strained lattice parameters, misorientation, bending radius and stress of ZnO films were estimated.
高温直接生长的样品弯曲半径小而应力更大;实验测量的应力值和理论计算的热应力值之间存在差异,原因主要是晶格失配应力的存在。
4) bend radius
弯曲半径
1.
Experiments of single mode fiber bend loss with the change of bend radius from 1 to 9 mm are made at 90° and 180°respectively.
系统对单模光纤弯曲损耗随弯曲半径(1~9 mm)进行90°和180°的弯曲实验,结果显示,光纤弯曲损耗随弯曲半径的增加呈下降趋势,光纤弯曲对不同波长的光损耗不同,且出现弯曲损耗的振荡,并进行了数值仿真和实验数据的比较。
2.
Based on field data of the river bend in middle and lower Hanjiang River and in Jingjiang River,the relation between the variation of bend radius of flow dynamic axis and bend bypassing and shoal cutting is expounded.
在分析汉江中下游以及荆江河湾实测资料的基础上,阐述了河湾水流动力轴线弯曲半径变化与切滩撇弯之间的关系,大量相关实测资料说明当河湾的来水条件和河湾形态发生变化时,会造成河势与水流动力轴线走向发生变化,从而引起切滩撇弯的发生。
5) radius of elbow
弯管半径
6) curve radius
弯曲半径
1.
Through analyzing and arranging the actual data measured of mountain area rivers in southwest of China,we summarize:The ideal channel flow route should have sine derivative curve flow route,harmonized flow direction,good flow route corner and bigger curve radius.
通过对西南地区山区河流实测资料进行分析整理 ,总结出 :正弦派生曲线水流线路、协调的水流方向、良好的水流转向角及较大的弯曲半径为理想的航道水流流路 ,并提出了该规律在工程设计中的应
补充资料：折半
1.减半;对折。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条