说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 参数化变形
1)  parametric deformation
参数化变形
1.
Here the deformation method is called parametric deformation technique, and the expression of the deformed curve apart from that of initial curve represents a curve called displacement curve.
提出一种曲线在几何约束下发生整体变形,且约束能够被精确满足的计算曲线变形的方法,该方法被称为参数化变形
2)  Parametric deformation of curve
曲线参数化变形
3)  deformation parameter
变形参数
1.
Analysis on three feature deformation parameters and multi damage of top coal in fully mechanized caving mining;
综放开采顶煤的三个特征变形参数及多次损伤分析
2.
Study on deformation parameters' characteristics of modified generalized Kelvin visco-elasto-plastic constitutive model of rock
修正的广义开尔文粘弹塑性岩石本构模型变形参数特性研究
3.
The unit reduction is a basic deformation parameter in cross rolling.
单位压下量是斜轧中的基本变形参数,提高单位压下量计算精度对于轧制力能参数计算和数值模拟建模具有重要意义。
4)  deformation parameters
变形参数
1.
Effect of plasticity index of saturated soft clay on its deformation parameters;
饱和软粘土的塑性指数对其压缩变形参数的影响
2.
Based on lab test & insitu test,the deformation parameters of paleo-clay in Qingshan area of Wuhan City is studied;and the bearing performance is studied by means of numeric simulation using ANSYS software and compared with the settlement observing data of the structures.
基于室内土工试验和现场试验成果,对武汉市青山地区的老粘土地基的变形参数进行研究;利用ANSYS有限元软件对老粘土地基进行数值模拟,并与构筑物地基沉降实测值对比,对地基承载性能进行研究。
3.
Using viscoelastic FEM for displacement reverse analysis, the viscoelastic deformation parameters and the geo stresses in the surrounding rock were analysed, and compared with the results of the actual deformation test and geostress measured in situ.
利用粘弹性有限元位移反分析方法对洞室围岩粘弹性变形参数及地应力条件进行了分析,并与岩体现场变形试验及地应力测量结果进行了比较。
5)  parameters change
参数变化
1.
Most manufacturers sterilize at 100℃ which can not satisfies F0≥8,we use a sterilization method which can reach F0≥8 to check the parameters change after sterilization.
本文针对小容量注射剂灭菌工艺进行探讨,由于大多数企业目前采用100℃对小容量注射剂进行灭菌,此工艺无法满足F0≥8,通过实验采用F0≥8的灭菌方式,考查灭菌后产品各参数变化。
6)  parameter variation
参数变化
1.
Taking parameter variation into account, a new model of the induced electromotive force relation of a permanent magnet synchronous motor (PMSM) was presented.
提出了永磁同步电动机考虑参数变化时精确的感应电势关系式新模型,建立了微分型和非微分型两种高精度感应电势观测器,证明了感应电势观测器的稳定性和收敛性,分析了参数变动对位置估计的影响。
2.
The authors analyze the influence in vector controlled induction machine caused by parameter variation and main flux saturation affects speed estimation of adaptive state observer.
通过MATLAB/SIMULINK仿真系统,建立静止坐标系下考虑磁饱和的感应电动机模型和矢量控制系统模型,并通过改变电机参数,比较分析参数变化及磁饱和效应对自适应状态观测器速度估计的影响。
3.
In this paper, a new modeling technique, Parameter Robust LQG algorithm, is introduced to handle structural parameter variations.
它是一种基于状态空间综合的方法,适用于不确定性参数变化形成结构性扰动的系统鲁棒性设计。
补充资料:大坝内部变形观测(见水工建筑物变形观测)


大坝内部变形观测(见水工建筑物变形观测)


  daba neibubianxing guanCe大坝内部变形观测见水工建筑物变形观测。
  
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条