1) hot deformation parameters
热变形参数
1.
Effect of hot deformation parameters on the microstructure of Ti53311S alloy;
热变形参数对Ti53311S合金组织的影响
2.
Analyses of the influence of hot deformation parameters on the real stress and microstructure of the LD7 aluminum alloy show that LD7 aluminum alloy is a kind of dynamic recovery alloy; flow stress declined with the increasd .
根据试验结果分析热变形参数对合金流动应力和固溶之后显微组织的影响 ,可以得到如下结论 :L D7铝合金是动态回复型合金 ,合金的流动应力随温度的升高而降低 ,随应变速率的升高而升高 ;合金的晶粒尺寸随温度的升高而增大 ,随变形程度和变形速率的增大而减小。
3.
Analyses of the influence of hot deformation parameters on the microstructure of the LD7 aluminum alloy show that the grain size of the LD7 aluminum alloy declines with the increase of the deformation and the strain rate, while it increases with the inc.
分析热变形参数对合金固溶后显微组织的影响 ,可以得到如下结论 :LD7铝合金的晶粒尺寸随温度的升高而增大 ,随变形程度的增大而减小 ,随变形速率的增大而减
2) thermo-deformation parameters
热变形参数
1.
Influence of thermo-deformation parameters on the flow stress of LD7 aluminum alloy;
热变形参数对LD7铝合金流动应力的影响
3) deformation parameter
变形参数
1.
Analysis on three feature deformation parameters and multi damage of top coal in fully mechanized caving mining;
综放开采顶煤的三个特征变形参数及多次损伤分析
2.
Study on deformation parameters' characteristics of modified generalized Kelvin visco-elasto-plastic constitutive model of rock
修正的广义开尔文粘弹塑性岩石本构模型变形参数特性研究
3.
The unit reduction is a basic deformation parameter in cross rolling.
单位压下量是斜轧中的基本变形参数,提高单位压下量计算精度对于轧制力能参数计算和数值模拟建模具有重要意义。
4) deformation parameters
变形参数
1.
Effect of plasticity index of saturated soft clay on its deformation parameters;
饱和软粘土的塑性指数对其压缩变形参数的影响
2.
Based on lab test & insitu test,the deformation parameters of paleo-clay in Qingshan area of Wuhan City is studied;and the bearing performance is studied by means of numeric simulation using ANSYS software and compared with the settlement observing data of the structures.
基于室内土工试验和现场试验成果,对武汉市青山地区的老粘土地基的变形参数进行研究;利用ANSYS有限元软件对老粘土地基进行数值模拟,并与构筑物地基沉降实测值对比,对地基承载性能进行研究。
3.
Using viscoelastic FEM for displacement reverse analysis, the viscoelastic deformation parameters and the geo stresses in the surrounding rock were analysed, and compared with the results of the actual deformation test and geostress measured in situ.
利用粘弹性有限元位移反分析方法对洞室围岩粘弹性变形参数及地应力条件进行了分析，并与岩体现场变形试验及地应力测量结果进行了比较。
5) variable heat parameter
变热工参数
6) parameters of deformation region
变形区参数
1.
In this paper, the technology parameters and the parameters of deformation region in forming process of the cross wedge rolling were introduced.
介绍了楔横轧成形过程的工艺参数及变形区参数 ,分析了楔横轧展宽区的金属变形情况及推导了变形区参数的工程计算公式。
补充资料：大坝内部变形观测(见水工建筑物变形观测)
大坝内部变形观测(见水工建筑物变形观测)
daba neibubianxing guanCe大坝内部变形观测见水工建筑物变形观测。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条