1) short carbon fiber
短碳纤维
1.
Processing and mechanical properties of short carbon fiber reinforced SiC matrix composites;
短碳纤维增强碳化硅基复合材料的制备
2.
Review on fiber homogenization techniques in fabrication of short carbon fiber reinforced composites;
短碳纤维复合材料中纤维均匀化技术的研究现状
3.
Electrical properties of short carbon fiber/nitrile batadiene rubber (SCF/NBR) composites;
短碳纤维增强丁腈橡胶复合材料的电性能研究
2) short carbon fibers
短碳纤维
1.
Study on application of short carbon fibers in electromagnetic shielding graphite concrete in low frequency;
短碳纤维在石墨低频电磁屏蔽混凝土中的应用研究
2.
The electromagnetic shielding properties of short carbon fibers and graphite concrete were investigated, and the influence for the contents of the short carbon fibers and graphite on the electromagnetic shielding effectiveness of the concrete in low frequency was studied.
对短碳纤维石墨混凝土的电磁屏蔽性能进行了研究,分析了短碳纤维和石墨的含量对混凝土低频电磁屏蔽效能的影响,探讨了短碳纤维的加入对石墨混凝土电磁屏蔽性能的影响机理,为设计高性能低频电磁屏蔽混凝土提供了依据。
3.
In this thesis, Composites made with Al-Cu alloys and SiC particales or short carbon fibers were prepared by powder metallurgy technology.
用不同的增强体材料碳化硅颗粒与短碳纤维来增强铝铜合金,并对加入不同体积分数增强体的铝基复合材料的力学性能进行了研究,并对其制备过程的烧结工艺及其随后的热处理工艺进行了优化,研究获得以下结果: (1)对复合材料的力学性能研究发现,界面结合的强弱影响很大,对增强体材料进行一定的预先处理以加强与改善基体材料的界面结合有利于提高材料的力学性能。
3) short carbon fiber
短切碳纤维
1.
Experimental study on compressive strength of short carbon fiber concrete
短切碳纤维钢筋混凝土板的平截面试验研究
2.
Preparation and property of short carbon fiber reinforced HA/PMMA bio-composites
短切碳纤维增强HA/PMMA生物复合材料的制备及性能
3.
Electromagnetic parameters of the ferrites and short carbon fiber composites were measured,and reflectivity of single-layer and double-layer composites with the thickness of 2mm is calculated in Ku waveband respectively.
使用溶胶凝胶法制备了M型和W型六角铁氧体,测量了铁氧体、短切碳纤维复合材料在Ku波段的电磁参数,并计算了层厚为2mm的单层和双层复合材料反射率。
4) short chopping carbon-fiber
短切碳纤维
1.
Silicon nitride ceramics were prepared by hot-press sintering method using α-Si3N4 power with short chopping carbon-fiber as starting materials,Y2O3-La2O3 and LiF-MgO-SiO2 as additives,respectively.
采用Y2O3-La2O3和LiF-MgO-SiO22组烧结助剂,通过短切碳纤维增韧的方法,热压烧结制备了氮化硅陶瓷,并对所得氮化硅陶瓷的相组成、微观结构和力学性能进行了分析和讨论。
2.
Csf/Si3N4 composites were prepared by hot-press sintering method using α-Si3N4 power,short chopping carbon-fiber as starting materials and sintering additives.
采用热压烧结的方法,以α-Si3N4粉和短切碳纤维为主要原料,以Y2O3和La2O3为烧结添加剂,制备Csf/Si3N4复合材料,研究了其力学性能和微波介电性能。
5) chopped carbon fiber
短切碳纤维
1.
Millimeter wave absorbing properties of reinforced composites with different length and content of chopped carbon fiber are investigated at the bands of 8mm(26.
本文研究了不同长度和含量的短切碳纤维复合材料在8 mm波段(26。
6) short carbon fibers
短切碳纤维
1.
An in-situ polymerizing and solution co-mixing approach was used in the formation of poly(methyl methacrylate)(PMMA) matrix composites using hydroxyapatite(HA) nano-particles and short carbon fibers(C(f)) as reinforcing materials.
以丙烯腈基短切碳纤维(C(f))为增强相、纳米羟基磷灰石( HA)为改性体,并以聚甲基丙烯酸甲酯(PMMA)为基体,采用原位合成与溶液共混相结合的方法制备了C(f)/ HA-PM-MA生物复合材料。
2.
Introducing preparation of electromagnetic shielding concrete containing short carbon fibers and ferrite power, properties of micro-wave transmission and absorbing are tested.
介绍了掺短切碳纤维和铁氧体粉末的电磁屏蔽混凝土的制备,测试了样品的电磁屏蔽性能,并比较了3mm与6mm短切碳纤维及其与铁氧体的复合结构在吸波混凝土中的屏蔽效能,分析、总结了实验样品中反映出来的规律,为设计高性能电磁屏蔽混凝土提供了依据。
3.
Improved PMR type polyimide matrix resin was synthesized by incorporating flexible ether-bridged segment into polyimide matrix resin, which was employed to impregnate short carbon fibers to yield molding compound.
采用分子组合技术,通过调节柔性芳基醚链段和刚性—C_6H_4—链段分子得到性能优良的PMR型聚酰亚胺基体树脂材料,将短切碳纤维与此种PMR型聚酰亚胺基体树脂通过湿法混合工艺得到聚酰亚胺复合材料模塑粉,采用热模压一次成型技术制备短切碳纤维增强聚酰亚胺复合材料,并对其性能进行系统的研究。
补充资料：聚丙烯腈碳纤维增强体(见聚丙烯腈碳纤维)
聚丙烯腈碳纤维增强体(见聚丙烯腈碳纤维)
carbon fibre reinforcements made of polyacrylonitrile
佩八饰”.限沂维用通体carbon fibre reinforce.ments made of polyaerylonitrile以聚丙烯睛纤维为原料制成的、角于复合材料中起承载增强作用和改善性能的碳纤维(见朵丙烯睛碳纤维).
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条