1) axial distortion parameter
轴向变形系数
1.
The axial distortion parameters can be calculated on the basis of the given intersection angles between the axes and the projecting angles produced in the projecting direction on the normal projecting system.
根据给定的轴间角计算轴向变形系数和根据给定的投影方向在正投影体系中的投影角计算轴向变形系数,从而在诸多正轴测投影表达方案中选出最佳表达方案。
2) axial deformation
轴向变形
1.
Influence of axial deformation and floor distortion on behaviors of hybrid structure;
轴向变形与楼板变形对混合结构受力性能的影响
2.
Building of test system on axial deformation of diamond circular saw blade
金刚石圆锯片轴向变形测试系统的构建与实验研究
3.
The change of temperature after or before gas well put into production will result in the variation of tubing string stress and axial deformation.
气井投产前后温度和压力变化会引起油管应力及轴向变形的改变。
3) axial deformation
轴向形变
4) horizontal transform coefficient
横向变形系数
1.
The basic mechanical properties of dry-mixing self-compacting concrete(SCC) in 28 days as well as the horizontal transform coefficient are studied experimentally and a great deal of experimental data including the cubical compressive strength,axial compressive strength and splitting strength are obtained.
文章通过试验方法,研究了干拌自密实混凝土的28 d基本力学性能及横向变形系数,获取了大量的干拌自密实混凝土立方体抗压强度、轴心抗压强度及劈裂强度的试验数据;分析了养护龄期和立方体抗压强度、劈裂强度之间的相关性,并提出回归公式。
2.
Modulus of elasticity,horizontal transform coefficient and peak strain which were had by dry-mixing Self-Compacting Concrete were studied.
研究了干拌自密实混凝土的弹性模量、横向变形系数以及峰值应变,分析了干拌自密实混凝土变形性能的特点,并根据统计分析给出了弹性模量的回归公式,试验结果表明,加水量对干拌自密实混凝土的弹性模量影响较大,横向变形系数与普通混凝土及高强混凝土均有较大差别,随着粗骨料含量的增加,干拌自密实混凝土的峰值应变减小。
5) rotation angle formula of the axial deformation
轴向变形转角位移函数
1.
In the paper,using Goodman′s elasticity intermediate layer hypothesis,considering all kinds of shear connectors,and introducing the rotation angle formula of the axial deformation,the deformation equilibrium differential equation of steel-concrete composite beams within the elastic limit was derived.
本文利用Goodman弹性夹层假设,可以考虑各种连接情况,通过引入轴向变形转角位移函数,推导了钢-混凝土组合梁在弹性范围内以挠度表达的平衡微分方程,得出了方程的通解和考虑界面滑移的挠度和轴向变形转角位移表达式,进而求出简支组合梁在集中和均布荷载作用下的内力和界面约束弯矩,以及混凝土板和钢梁截面内力和界面滑移量。
6) axial factor
轴向系数
补充资料：变形区形状系数
变形区形状系数
parameters of deformation zone
b ianxingqu xingzhuang xishu变形区形状系数(parameters of deformationzone)通常指反映变形区几何特征及这些特征在轧制过程中对应力状态影响程度的轧件和工具尺寸的。~一~一，二。，了二H十川，，，。小二，，~参数，主要有z仄、R仄(万一号二}，H/D或从/D。式中D、R、H、h、万、l分别指轧辊直径、轧辊半径、轧件轧前厚度、轧件轧后厚度、轧件平均厚度、变形区长度。 (余望)
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条