1) stress graph
应力图形
1.
Problems existing in reinforced concrete beam reinforcement design with tensile stress graphs;
钢筋混凝土梁用拉应力图形配筋存在问题的探讨
2.
Effect of simplified stress graph of concrete on bending strength of its cross-section;
混凝土应力图形简化对截面抗弯强度的影响
2) rectangular stress block
矩形应力图
1.
The modified rectangular stress block can be applied to both normal\|strength and high\|strength concrete sections, and the result obtained is better consistent with the test data than the code.
在 Ibrahim等建议的修正公式基础上 ,对我国规范混凝土矩形应力图参数提出修正 ,使混凝土矩形应力图不仅能应用于普通混凝土 ,还可推广应用于高强混凝土 。
3) normal stress figure
正应力图形
4) forming limit stress diagram
成形极限应力图
1.
A new method for establishing forming limit stress diagram of sheet metals;
一种建立板料成形极限应力图的新方法
2.
Based on the experimental results,the FLSD(forming limit stress diagram) was determined.
论述了硬铝合金成形工艺中应变路径、固溶热处理和时效过程对成形极限的影响,由试验得到了单向拉伸预应变和固溶热处理后时效过程中的成形极限图FLD(Form-ing Lim itD iagram),重点研究了固溶热处理后时效过程中成形极限的变化,并得到了铝合金在时效过程中的成形极限应力图FLSD(Form ing Lim it Stress D iagram)。
3.
In view of the above reason, this thesis adopts the forming limit stress diagram as the in.
本文基于板成形专用有限元分析软件DYNAFORM,以国内外板料成形领域认同的具有应变路径独立性优点的成形极限应力图为判据进行了应用软件的二次开发,以期为板成形有限元分析软件提供一个新的失稳判据。
5) forming limit stress diagram
应力成形极限图
1.
A program of forming limit stress diagram is developed based on the finite element software Dynaform.
根据极限应变到极限应力的转换关系,采用 Hill48塑性准则和 Hill79塑性准则建立了应力成形极限图的数学计算模型。
2.
The forming limit stress diagram(FLSD) which established with limit stress is independent on the strain paths and it is practical to use as the criterion of forming limit under cmplex strain paths.
由极限应力构成的应力成形极限图(FLSD)独立于应变路径,可作为复杂应变路径下成形极限的判据。
3.
Forming limit diagram is used for analyzing sheet forming in finite element analysis software have proposed forming limit stress diagram which is not relies on the loading path.
但它是依赖于加载路径的, 用它来分析多道次板成形是不合适的,于是人们提出了与加载路径无关的应力成形极限图。
6) equivalent rectangular stress block
等效矩形应力图
1.
Investigation on characteristic values of equivalent rectangular stress block of non-uniform compression stress in polygon;
关于混凝土多边形非均匀受压区的等效矩形应力图探讨
补充资料：轧辊残余应力(见轧辊应力)
轧辊残余应力(见轧辊应力)
residual stresses in roll
zhagun eanyu yingli轧辊残余应力(residual stresses in roll)见礼辐应力。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条