2) power capacitor
电力电容器
1.
Simple Analysis of The Fire Prevention in Power Capacitor;
电力电容器火灾预防浅析
2.
Study on power capacitor overvoltage;
电力电容器过电压的研究
3.
Modeling and simulation of abruption test of power capacitor and the measurement system;
电力电容器爆破能量试验及其检测系统的建模与仿真
3) electric power capacitor
电力电容器
1.
New solutions of abnormal settings of WKBCI device under-voltage protection for electric power capacitor;
WKBCI装置电力电容器欠压保护动作电压异常的新解决方案
2.
The vacuum technology of double-pumping-and-single-filling-type electric power capacitor is to combine vacuum pre-drying,vacuum drying,vacuum impregnating and pressure impregnating,namely to finish integrated heating,vacuum drying and vacuum pressure impregnating in the same vacuum container.
"双抽单注式"电力电容器真空工艺是将真空预干燥、真空干燥、真空浸渍、加压浸渍等数道工艺合并,在同一台真空罐内进行一体化的加热、真空干燥和真空压力浸渍。
3.
main specification,design outline and representative application of asynchronous generator,and lists the specification of electric power capacitor for asynchronous generator.
论述了异步发电机的分类、结构和工作原理、主要技术指标、设计要点以及典型应用,给出了异步发电机配套用电力电容器技术数据。
4) electric condenser
电力电容器
1.
Analysis of influence of electric current of wave in harmony on electric condenser;
谐波电流对电力电容器的影响
2.
It introduces the reason why the electric condenser explodes points out the general omen before the exploding of the electric condenser and describes the measures of preventing the electric condenser from exploding .
介绍了电力电容器爆炸的原因,指出了电力电容器在爆炸前的一般预兆,论述了防止电力电容器爆炸的措施。
5) power condenser
电力电容器
1.
The analysis for abnormal operation of power condenser in Shizuishan Electric Power Supply Bureau;
石嘴山供电局电力电容器的异常运行分析
2.
The basic structure and corresponding investigation test of vacuum type and whol e scope current limiting f use were introduced,which is used f or protecting single power condenser and domestic R&D independently,and the require ment of special design was given.
介绍了我国自行开发研制的保护单台电力电容器真空式全范围限流熔断器的基本结构和相应的研究性试验,给出了特殊设计的要求,以及较详细介绍了额定电压为6kV、额定电流为50A、开断电流为40kA的保护电力电容器用熔断器的设计范例。
补充资料：电力电容器灌封料
分子式：
CAS号：
性质：树脂(A)为聚醚填充料等，固化剂(B)为改性异氰酸酯等。由聚醚与辅助材料经脱水精制后再加填充料和催化剂进行反应，然后经研磨混合、过滤而成。树脂为白色或黄色黏液。密度1.35～1.40g/cm3。黏度(25℃)7000mPa·s左右。固化剂为黑色或黄色黏液。密度1.10～1.15g/cm3，黏度(25℃)5500mPa·s左右。用于电容器元件特别适用于电力电容器的表面密封和固定。
CAS号：
性质：树脂(A)为聚醚填充料等，固化剂(B)为改性异氰酸酯等。由聚醚与辅助材料经脱水精制后再加填充料和催化剂进行反应，然后经研磨混合、过滤而成。树脂为白色或黄色黏液。密度1.35～1.40g/cm3。黏度(25℃)7000mPa·s左右。固化剂为黑色或黄色黏液。密度1.10～1.15g/cm3，黏度(25℃)5500mPa·s左右。用于电容器元件特别适用于电力电容器的表面密封和固定。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条