1) unconstrictive monomer
无收缩单体
1.
Recently alicyclic epoxy compound with high thermal stability but large volume shrinkage during curing [1] and unconstrictive monomer with low volume shrinkage but low thermal stability [2] have been developed respectively.
无收缩单体-1,6,8,13-四氧螺[7,7]十三碳烷(SOC_7)和脂环族环氧树脂-3,4-环氧基环已烷甲酸3′,4′-环氧基环已烷甲酯(ERL-4221)的光引发正离子共聚合的研究结果表明,少量SOC_7加到ERL-4221体系中可抑制固化收缩没有明显降低热性能。
2) non-shrinkage
无收缩
1.
Experimental study on cement-based non-shrinkage composite grouting material;
水泥基无收缩复合灌浆料的实验研究
2.
HL-HGM high strength non-shrinkage grouting material is a kind of grouting material characterized as high strength, non-shrinkage and high fluidity.
HL-HGM高强无收缩灌浆料是一种高强度、无收缩、流动性大的灌浆材料,本文研究了不同水料比对灌浆料的流动度、泌水率、凝结时间、强度等性能的影响,简要介绍了产品在杭州湾跨海大桥50m简支箱梁支座安装中的应用,与环氧树脂砂浆灌浆相比,具有施工工艺简单,施工进度快,工程质量高,节约成本,环保等特点。
3.
This thesis mainly introduces CGM high-strength non-shrinkage grouting material construction technical features and requirements in P.
本文主要介绍了CGM高强无收缩灌浆料用于北京理工大学体育馆工程的施工技术特点、技术要求和施工工艺。
3) single contraction
单收缩
1.
Methods The single contraction curves of toad gastrocnemius muscles(n=94)stimulated continuously(912ms,7.
8任氏液中的蟾蜍离体腓肠肌 (n =94 )的单收缩曲线。
4) Volume shrinkage
体积收缩
1.
Influence of volume shrinkage on isothermal crystallization kinetics of polymer;
体积收缩对高聚物等温结晶动力学过程的影响
2.
Effect of CaCO_3 fillers on volume shrinkage of unsaturated polyester and their mechanism;
碳酸钙填料对不饱和聚酯树脂体积收缩的影响及其机制
3.
Volume shrinkage ratio was analyzed from two aspects,the aging-swelling balance and solvent effect.
介绍了三聚氰胺-甲醛凝胶老化过程的溶剂效应及其对体积收缩的影响。
5) volumetric shrinkage
体收缩率
1.
L27(313) experiments were performed in order to determine an optimum condition for minimizing the volumetric shrinkage in multi-cavity injection molded parts of polypropylene(PP).
选用L27(313)正交表设计实验,研究模具温度、熔体温度、充填时间、保压压力和保压时间以及三个两因素交互作用对多型腔模具PP塑料制品每个型腔体收缩率的影响程度。
6) volumetric shrinkage
体积收缩
1.
The volumetric shrinkage of the two proposed resins is measured to be around 5 5%.
针对目前所使用的自由基型紫外光固化树脂体系的体积收缩率较大的问题 ,采用一种新型的大相对分子质量齐聚物与环氧丙烯酸酯齐聚物混合 ,通过优化配方 ,得到体积收缩率分别为5 4 %和 5 7%的两种高性能光固化树脂 ,在 30℃时它们的粘度分别为 360mPa·s和 5 2 0mPa·s ,而且均具有较高的固化速度和拉伸强度 。
2.
The effects of injection-molding processing parameters on the volumetric shrinkage of plastic-lens are studied by Taguchi method.
利用CAE技术来模拟塑料镜片的注射成型,通过模拟分析不同注塑成型工艺参数下塑料镜片的体积收缩率。
补充资料：收缩中(晚）期喀喇音-收缩晚期杂音综合征
收缩中(晚）期喀喇音-收缩晚期杂音综合征
即"二尖瓣脱垂-喀喇音综合征"。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条