1) shallow charge-discharge
浅充放
2) to enable an opponent to win by discarding a tile
放充; 放炮
3) shallow hole drainage
浅孔抽放
1.
According to the underground pressure distribution rule and the separation control function of drainage borehole,the shallow hole drainage technology is studied and tested by using the characteristic that the gas permeability may have an obvious increase after mining in front of the working face,obtaining some useful parameters,showing that the tech.
根据矿山压力分布规律和抽放钻孔的隔断控制作用,并利用工作面前方煤体受采动卸压后透气性显著提高这一特性,研究并试验了卸压区浅孔抽放技术,获得了该抽放技术的工艺参数。
2.
Mucus sealing is used in coal shallow hole drainage to seal the cracks around the hole.
采用粘液密封钻孔周围裂隙是解决浅孔抽放过程中空气大量泄露的有效方法。
4) charge-discharge
充放电
1.
The charge-discharge cycles showed that Ti-doped sample prepared at 600℃,spinels without doping sintered at 600 and 750℃,exhibited a initial capacity of 205,189 and 207mAh/g in the 1st 40-cycles,respectively.
充放电实验表明,在4。
2.
Screening battery from its charge-discharge characteristics is an unique trait peculiar to this system.
采用三级计算机控制方式、多功能电池夹具和模块化结构研制的二次电池检测系统,具有功能多、性能稳定和实用性强的特点,还独创了按充放电性能曲线分选电池的功能。
3.
During the charge-discharge cycles of amorphous (Mg_(60) Ni_(25))_(90)Nd_(10) alloy,NdMg_2 Ni_9 phase appears after four cycles and Mg_2 Ni phase appears after six cycles.
5) Nd_(10)在充放电循环中的组织演变。
5) constant current charge/discharge
恒流充放
1.
The electrochemical properties were tested by cyclic voltammetry and constant current charge/discharge.
循环伏安结果表明该材料具有良好的电容性能,用恒流充放电测得在1mA条件下,放电比电容可达290。
2.
The electrochemical properties were tested by cyclic voltammetry,AC impedance and constant current charge/discharge in threeelectrode system.
按m(MnO2)∶m(石墨)∶m(乙炔黑)∶m(羧甲基纤维素)∶m(聚四氟乙烯)=75∶10∶10∶3∶2制备电极材料,在电解液为c〔(NH4)2SO4〕=2mol/L的三电极体系中,通过循环伏安、交流阻抗和恒流充放电对其超级电容性能进行了考察。
6) charge/discharge
充电/放电
1.
The "charge/discharge" roles of the basin-wide mode of the Indian Ocean SST anomaly——influence on the South Asian High in summer;
热带印度洋SST海盆模态的“充电/放电”作用——对夏季南亚高压的影响
补充资料：充炭黑充油丁苯橡胶
分子式：
分子量：
CAS号：
性质：同时含有炭黑和油的丁苯橡胶。性能和用途与充炭黑丁苯橡胶和充油丁苯橡胶相似。由冷聚丁苯胶乳与炭黑的水分散液和油乳液经混合、凝聚、洗涤、过滤、干燥等步骤制得。
分子量：
CAS号：
性质：同时含有炭黑和油的丁苯橡胶。性能和用途与充炭黑丁苯橡胶和充油丁苯橡胶相似。由冷聚丁苯胶乳与炭黑的水分散液和油乳液经混合、凝聚、洗涤、过滤、干燥等步骤制得。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条