1) pressure components inside boiler
![点击朗读](/dictall/images/read.gif)
炉内承压部件
1.
High temperature superheater is taken for example to analyze the life loss rule of pressure components inside boiler.
本文以高温过热器为例,对锅炉炉内承压部件的寿命损耗规律进行了分析,采用拄森-米勒参数式确定蠕变断裂时间,用罗宾逊法则求出过热器蠕变寿命损耗,同时考虑疲劳对高温金属的破坏作用,最终得到适用于在线监测系统的过热器蠕变寿命简化计算公式。
3) pressure element
![点击朗读](/dictall/images/read.gif)
承压部件
1.
In the light of the fact that elastic creep damage happens to heat resistant steel used as pressure elements like steam pipeline and steam pockets in heat-engine plants at high temperature and under high pressure,this article gives a complete constitutive description of the damage,building up the theory of phenomenology about creep damage.
针对火电厂中蒸汽管道与汽包类承压部件用的耐热钢 ,在承受高温高压时发生弹性蠕变损伤问题 ,给出完整的损伤本构描述 ,建立起唯象学蠕变损伤理论。
4) pressure-containing member
![点击朗读](/dictall/images/read.gif)
承压部件
1.
The pressure-containing member jointing is one of the cores during the boiler installation.
工业锅炉的安装,其承压部件的焊接是锅炉安装核心之一。
5) main pressure parts of boiler
![点击朗读](/dictall/images/read.gif)
锅炉承压件
6) attachment of nonpressure parts
![点击朗读](/dictall/images/read.gif)
非承压部件
补充资料:将UG里的一个装配部件输出成单个部件文件
法一:
- 关闭(turn off)FileàOptions->Load Options下"Partial Loading "选项
- 打开装配部件
- 选择File->Export->Part
- 在"Part Specification"下选择"new"
- 选择"Specify Part",指定输出部件文件名称及位置
- 将"Object Selection Scope"设定为"All Objects"
- 选择"Class Selection->Select All"高亮所有对象
- 按"OK"
该种方法特点:每一个部件的特征都会汇集在新部件的MNT里。可以方便编辑。
法二:
- 闭(turn off)File->Options->Load Options下"Partial Loading "选项
- 打开装配部件
- Application->Assembly
- Assemblies->Components->Create New,给出想要输出的部件文件名及路径。
- 如下图1,在ANT上双击新产生的部件文件,使其成为工作部件。
- Assemblies->WAVE Geometry Linker,将设置改为"Body",选择所有组件的体。
- 将"Create Non-associative"开关设为"On",见下图2
- 将产生的部件设成显示部件,仅保存刚产生的新部件,不保存旧的装配部件。
![]() 图1 | ![]() 图2 |
该种方法特点:每一个部件在新部件的MNT里只会显示一个link的特征。没有相应特征可以编辑。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条